FUTABA 12Z Series - Page 58

58
<Functions of Linkage Menu>
PUSH
[Cursor Lever]
Ɣ0RYHPHQWRQWKH
VFUHHQGLUHFWLRQV
Ɣ3XVKWKHOHYHUWRFDOO
QH[WSDJH
[Data Input Dial]
[Enter Button]
[Return Key]
Ɣ7RKRPH
VFUHHQ
Ɣ7RSUHFHGLQJ
VFUHHQ
SERVO-REVERSE
8VHWRUHYHUVHWKHWKURZGLUHFWLRQ
Servo Reverse changes the direction of an
individual servo’s response to a control stick
movement.
For CCPM helicopters, be sure to read the
section on Swash AFR before reversing any servos.
With CCPM helicopters, always complete your
servo reversing prior to any other programming.
If you use pre-built Airplane/Sailplane functions
Servo reversing procedure
*After linkage of a new model is complete, check whether or
not each servo is connected to the correct channel.
*Next, determine whether you need to reverse any channels
by moving each stick.
8VHWKHFXUVRUOHYHUWRPRYHWKHFXUVRUWRWKH
FKDQQHO\RXZDQWWRUHYHUVH
7XUQWKHGDWDLQSXWGLDODQGFKDQJHWKH
GLVSOD\WR>5(9(56(@RU>1250$/@
*The display blinks.
:KHQWKHHQWHUEXWWRQLVSXVKHGVHUYR
RSHUDWLRQLVUHYHUVHG2SHUDWHDQRWKHUNH\
WRVWRSUHYHUVDO
*Repeat the operation above for each channel that must be
reversed.
that control multiple servos, it may be confusing
to tell whether the servo needs to be reversed or a
setting in the function needs to be reversed. See the
instructions for each specialized function for further
details. Always check servo direction prior to every
ÀLJKWDVDQDGGLWLRQDOSUHFDXWLRQWRFRQ¿UPSURSHU
model memory, hook ups, and radio function.
(The display screen is an example. The screen depends on the model type.)
ŏ6HOHFW>6(5925(9(56(@DWWKHOLQNDJHPHQXDQG
FDOOWKHVHWXSVFUHHQVKRZQEHORZE\SXVKLQJWKH
HQWHUEXWWRQ
ﶮ﷊ﶰﶨﶶﶀﶰ﷊ﶨ﷊ﶰﶮ﷊
﷎ﷄ
ﴶﴸﴸﳜ
﷤
﷢
﷠
﷞
﷈ﶪﶸ﷎ﶬﷂﶶﶸ
８６０：Ｒ＜
ﶮ﷊ﶬﶬﷂﶸﷆ
﷊ﶼ﷊ﶨ﷒ﶬﶶﶰ
ﶰﶪ﷌﷌﷊ﶰ
ﶬﷄﶰﶶﶬﶬﶼ﷊
﷒ﷂﶼ﷊ﶰﶶﶸ
８６０：Ｒ＜
８６０：Ｒ＜
８６０：Ｒ＜
ﶺﶶ﷌﷊ﶼ﷤
﷎ﶶﶸ﷌ﷂﶬ﷤
ﴶﴸﳰﴶﴸﳰﴸﴸ