FUTABA R7008SB Instruction Manual

Applicablesystems:FutabaFASSTest-2.4GHz
systemtransmitter
ComplianceInformationStatement(forU.S.A.)
This device, trade name Futaba Corporation of America, model number R7008SB, complies with part15 of the
FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
(3) This module meets the requirements for a mobile device that may be used at separation distances of more than
20cm from human body.
To meet the RF exposure requirements of the FCC this device shall not be co-located with another transmitting
device.
The responsible party of this device compliance is: Futaba Service Center 3002 N Apollo Drive Suite 1,
Champaign, IL 61822 U.S.A. TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)
R7008SBSpecifications
FASSTest-2.4GHz system(18CH/12CH mode)/
S.BUS2 and S.BUS port and 8 channels for conven-
tional system receiver
• Dual antenna diversity
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)
• Weight: 0.38 oz. (10.9g)
• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to
8.4V)
• Battery F/S Voltage: It sets up with a transmitter
• Extra Voltage port: 0
〜
70V DC
* Be sure that when using ESCs regulated output the capacity of the
ESC must meet your usage condition.
LEDIndication
Green Red Status
Off Solid No signal reception
Solid Off Receiving signals
Alternate blink Unrecoverable error (EEPROM, etc.)
(Antenna installation)
90˚
Please refer the table below for
LED status vs receiver's condition.
1M23N17491
＋
−
6%86
SRUW
6%86SRUW 6%ك
6%86ك
56%
7HUPLQDOER[
6%866HUYR
6%86*\UR
+8%
+8%
+8%
+8%
([WUD9ROWDJH
3RUW
/LQN0RGHVZLWFK
$QWHQQD
/('
6HUYRIRU FRQYHQWLRQDO
V\VWHP
&KDQQHORXWSXW
&KDQQHORXWSXW
7HPSHUDWXUH
6HQVRU
530
6HQVRU
9ROWDJH
6HQVRU
9ROWDJH
6HQVRU
$OWLWXGH
6HQVRU
$OWLWXGH
6HQVRU
6%867RRO
,WLVQRWXVHGIRUDOLQN
Itconnectswiththe
batteryforpower,etc.
Externalvoltageinput
cableofanoptionis
used.Thevoltageof
thebatterycanbe
displayedwitha
transmitter.
Usageprecaution
• Analog servos cannot be used with the
R7008SB in the FASSTest 12CH mode.
• The R7008SB receiver can only be used
with FASSTest capable transmitters.
• Don't connect to Extra Voltage before turn-
ing on a receiver.
WARNING
Changes or modification not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
The R7008SB receiver should be protect-
ed from vibration by foam rubber, Velcro
or similar mounting methods. Protect
from moisture.
Keep away from conductive materials to
avoid short circuits.
Antennainstallationprecaution
Do not cut or bundle the receiver antenna
wire.
Do not bend the coaxial cable. It causes
damage.
The antennas must be mounted in such a
way to assure they are strain relieved.
Keep the antenna as far away from the motor,
ESC and other noise sources as you possibly can.
Be sure that the two antennas are placed at 90
degrees to each other.
• The R7008SB has two antennas. In order to maximize signal
reception and promote safe modeling Futaba has adopted a
diversity antenna system. This allows the receiver to obtain
RF signals on both antennas and fly problem-free.
Antennainstallationforcarbonfuselage
WARNING
You must leave 30mm at the tip of the antenna
fully exposed. The exposed antenna should be
secured so that it cannot move around or back
inside of your aircraft.
S.BUS2precaution
DANGER

Don't connect a connec-
tor, as shown in a before
figure.
• It will short-circuit, if it connected
in this way. A short circuit across
the battery terminals may cause
abnormal heating, fire and burns.
WARNING
Only S.BUS2 capable devices may be connected
to the S.BUS2 port. Standard S.BUS servos and
gyros should not be connected to the S.BUS2 port.
(Typical installation)
FASSTest-2.4GHz Bidirectional
Communication System
S.BUS2 / S.BUS Port and 8 Channels for
Conventional System

Receiver
R7008SB
Thank you for purchasing a Futaba R7008SB FASSTest-
2.4GHz compatible receiver. The R7008SB receiver features bi-
directional communication with a FASSTest Futaba transmitter
using the S.BUS2 port. Using the S.BUS2 port an impressive
array of telemetry sensors may be utilized. It also includes both
standard PWM output ports and S.BUS output ports.
S.BUS2
5HFHLYHU
Do not insert either a switch
or battery in this manner.
DANGER
Instruction Manual

FUTABA R7008SB Specifications

General

Brand	FUTABA
Model	R7008SB
Category	Transmitter
Language	English