This document is a user manual for the FUXTEC FX-RM5170agile petrol lawnmower, providing instructions and safety guidelines in multiple languages.
Function Description:
The FUXTEC FX-RM5170agile is a petrol lawnmower designed exclusively for mowing lawns in private areas. It is equipped with a 4-stroke, air-cooled OHV engine. The mower offers various features to facilitate lawn care, including cutting height adjustment, mulching capability, and side ejection. It is designed for ease of use and maintenance, with clear instructions for assembly, operation, and routine servicing.
Important Technical Specifications:
- Engine: OHV, air-cooled, 4-stroke
- Nominal power: 2.9 kW
- Engine speed: 2800 U/pro Minute (RPM)
- Displacement: 170 cm³
- Starter: Recoil (and eStart for eS-models)
- Tank volume: 1.0 l (for petrol)
- Oil tank volume: 0.5 l
- Cutting heights: 25mm - 75mm
- Cutting width: 508 mm
- Diameter wheels: 18 cm front / 23 cm rear
- Grass collector volume: 60 l
- Sound power level: 98 dB
- Vibration: 3.64 km/h
- Weight: 37.5 kg
Usage Features:
- Assembly: The manual provides detailed steps for assembling the upper and lower tie bar, mounting the control panel, and attaching the grass collector. It also covers the installation of the mulch kit and the side ejection chute (if applicable to the model).
- Handlebar Adjustment: The handlebar height can be adjusted using "L" (low) or "H" (high) holes on the brackets, fixed with screws and buttons.
- Starting the Engine: For a cold start, the primer pump should be pressed (if equipped) before engaging the throttle grip. The engine is started by pulling the starter cable. For models with rear-wheel drive, the rear-wheel drive handle should not be held during starting to prevent immediate movement.
- Stopping the Engine: The engine is stopped by pulling back the lever and then releasing the engine drive lever.
- Cutting Height Adjustment: The desired cutting height (25mm-75mm) is set using a dedicated lever. This operation should only be performed when the engine is switched off and the cutting blade is stationary to prevent injury.
- Front Wheel Adjustment: The front wheel direction can be fixed to face forward ("CLOSE" position) or allowed to swivel ("OPEN" position) for better maneuverability around obstacles.
- Mulching Function: The included mulch kit allows blocking the rear discharge opening, causing the grass to be shredded further by the blade and returned to the lawn.
- Side Ejection: For models with side ejection, the side discharge chute can be hooked in after lifting the cover.
- Fuel and Oil: The mower is delivered without fuel and oil. Users must fill 1.0 liter of regular petrol (minimum 95 octane) and 0.5 liter of oil before the first use. The oil level should be between the upper and lower marks on the dipstick.
- Variable Engine Speed: For optimal cutting quality, the engine should always be operated at the "FAST" throttle position, which creates a powerful fanning effect to lift and cut grass efficiently.
Maintenance Features:
- General Maintenance: Regular maintenance is crucial for safety and performance. This includes ensuring all nuts, bolts, and screws are properly tightened.
- Blade Maintenance: The cutting blade should be regularly checked for damage, cracks, rust, or excessive wear. Dull blades can be sharpened, but excessively worn or damaged blades must be replaced. A torque spanner should be used for installation, and work gloves are recommended. A wooden block can be used to prevent the blade from turning during removal and tightening.
- Easy Clean Function: Some models feature a water connection on the left side of the mower deck for cleaning. To use, connect a hose, turn on the water, and start the engine. The rotating blades will clean the underside of the deck. This should be done with the mower in the lowest height position.
- Air Filter: The air filter should be regularly checked for damage and cleaned by tapping it or blowing compressed air from the inside. Brushing should be avoided as it pushes dirt into the fibers. The air filter housing should also be wiped clean.
- Spark Plug: The spark plug needs a correct gap (0.028 ~ 0.031 inch or 0.7 ~ 0.8 mm) and must be free of deposits for good performance. It should be checked for wear, cracks, or fissures and replaced if necessary. A spark plug spanner is required for removal and installation (not included).
- Cable Adjustment: Before operation and after the first season, control cables (for drive, engine brake, and throttle) should be checked for tautness and adjusted if necessary, as they may stretch with use.
- Storage: For long-term storage, the mower should be thoroughly cleaned and stored in a dry place. Fuel should not remain in the tank for more than one month. The engine must be cooled down before storing in an enclosed space, and the fuel tank should be emptied outdoors to reduce fire risk.
- Disposal: Information on disposal options should be obtained from local authorities, emphasizing recycling raw materials.
Need help?
General
To Next Page
