What to do if my Gabarron CM15 shows Error E3 Lack of heating water flow?
Error E3 means there is a lack of heating water flow. This could be because the pump is blocked – unblock it. Also, check if any valves are shut and open them. Another reason might be air in the installation, so purge the installation.
What to do if my Gabarron Boiler shows Error E4 Overheating of the heating?
Error E4 indicates overheating, which may be due to a blocked pump. Unblock the pump. Alternatively, check if any valves are shut and open them. Air in the installation can also cause this, so purge the installation.
How to fix Gabarron Boiler that will not start?
If your Gabarron Boiler won't start, there could be several reasons. First, ensure the boiler is receiving power by checking the incoming power supply. Also, verify that the boiler control switch is turned on. If the heating system overheated, the switch may have tripped; locate and reset it. The same applies to DHW overheat. Lastly, if the DHW tank is empty, open a hot water tap until water flows.
What does fault E5 mean on a Gabarron Boiler?
If your Gabarron Boiler displays fault E5, it indicates an error in the configuration for maximum heat output. You should check the correct configuration.
What does fault E6 on my Gabarron Boiler mean?
If your Gabarron Boiler displays fault E6, it indicates a problem with the DHW temperature sensor. Check the connections. If necessary, replace the sensor.
Why is my Gabarron Boiler heating temperature so low?
If your Gabarron Boiler is producing low heating temperature, first check the temperature and output settings to ensure they are appropriately configured. Also, check the heating elements and replace if necessary. Finally, it's possible the heat requirements were miscalculated; recalculate and configure accordingly.
What does it mean if Gabarron CM15 Boiler displays fault E3 and system resistance is too high?
If your Gabarron Boiler displays fault E3, and it continues, the system resistance might be too high or there could be a blockage. Verify pump speed 3, check pump duty, open all radiator valves, and install a system by-pass.
What does it mean if Gabarron CM15 displays fault E3 and there is air in the system?
If your Gabarron Boiler displays fault E3, and it continues, there might be air in the system. Purge the system thoroughly. Check that the automatic air valve is open. Vent the pump.
What does it mean if Gabarron CM15 displays fault E3 and the pump is not turning?
If your Gabarron Boiler displays fault E3, and it continues, the pump may not be turning. Check that it is rotating freely. If necessary, replace the pump.
What to do if the buttons on my Gabarron Boiler do not respond?
If the buttons on your Gabarron Boiler do not respond, the control panel may be blocked. Consult Section 10.2 BLOCKING THE CONTROLS for instructions.
Explains the boiler's heating capabilities and operation.
Lists the main internal components and their materials.
Identifies numbered components in a diagram.
Details safety features and controls within the boiler.
Outlines installation compliance with standards and regulations.
Lists items included in the boiler packaging.
Details requirements for installing unvented hot water systems.
Specifies suitable siting requirements for the boiler.
Provides dimensional drawings and connection points.
Specifies minimum clearances required around the boiler.
Instructions for fitting the wall mounting bracket.
Details how to connect water pipes to the boiler.
Specifies requirements for discharge pipework from safety valves.
General information on electrical connections to the boiler.
Specifies cable sizes, MCB/RCD ratings for different boiler outputs.
Details mains connection procedures and bridging for voltage selection.
Explains connecting external controls like thermostats.
How to configure the boiler's maximum output using switches.
Step-by-step guide for filling the heating system.
Procedures for checking and venting the circulation pump.
Guidance on flushing the heating installation before operation.
Instructions for filling the domestic hot water system.
Crucial steps before turning the boiler on for the first time.
Explains the functions of buttons and indicators on the control panel.
How to operate and set the domestic hot water temperature.
How to operate the central heating function and adjust temperature.
Explains the frost protection mode and its activation.
Describes the automatic modulation for energy saving.
How to lock the control panel to prevent unauthorized adjustments.
Explains the pump's anti-seize function during inactivity.
Lists common problems, their causes, and solutions.
Details how to reset overheat safety cut-outs.
Explains the E3 error and the need for system by-pass.
Procedure to verify the boiler's configured heat output.
To Next Page
General
