Garmin RV - User Manual

RV FIXED DISPLAY
INSTALLATION
INSTRUCTIONS
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
CAUTION
To obtain the best performance and to avoid damage to your
RV, install the device according to these instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin
®
Product Support.
Loading the New Software on a Memory Card
1
Insert a memory card into the card slot on the computer.
2
Go to www.garmin.com, and locate the product page.
3
Select Software from the product page.
4
Select Download.
5
Read and agree to the terms.
6
Select Download.
7
Select Run.
8
Select the drive associated with the memory card, and select
Next > Finish.
Updating the Device Software
Before you can update the software, you must obtain a
software-update memory card or load the latest software onto a
memory card.
1
Turn on the device, and wait for the home screen to appear.
NOTE: In order for the software update instructions to
appear, the device must be fully booted before the card is
inserted.
2
Open the memory card door .
3
Insert the memory card , and press it in until it clicks.
4
Close the door.
5
Follow the on-screen instructions.
6
Wait several minutes while the software update process
completes.
The device returns to normal operation after the software
update process is complete.
7
Remove the memory card.
NOTE: If the memory card is removed before the device
restarts fully, the software update is not complete.
Contacting Garmin Support
• Go to support.garmin.com for help and information, such as
product manuals, frequently asked questions, videos, and
customer support.
• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.
Tools Needed
• Drill
• 6 mm (
1
/
4
in.) drill bit
• 4 mm (
3
/
16
in.) drill bit
• #2 Phillips screwdriver
• Jigsaw or rotary tool
• File and sandpaper
Mounting Considerations
NOTICE
This device should be mounted in a location that is not exposed
to extreme temperatures or conditions. The temperature range
for this device is listed in the product specifications. Extended
exposure to temperatures exceeding the specified temperature
range, in storage or operating conditions, may cause device
failure. Extreme-temperature-induced damage and related
consequences are not covered by the warranty.
When selecting a mounting location, you should observe these
considerations.
• The location should allow for easy access to all device
interfaces, such as the keypad, touchscreen, and card
reader, if applicable.
• The location must be strong enough to support the weight of
the device and protect it from excessive vibration or shock.
GUID-D7562D38-5D0D-465B-8FF1-97809D4F9CA6 v1March 2020

Summary

Important Safety Information and Installation Procedures

Loading New Software onto Memory Card

Steps to prepare a memory card with the latest software for device updates.

Updating Device Software

Procedure to update the device software using a prepared memory card.

Contacting Garmin Support

Contact information and resources for obtaining Garmin product support.

Tools Needed for Installation

List of tools required for the installation process.

Mounting Considerations

Guidelines for selecting an appropriate and secure mounting location for the device.

Flush Mounting the Device

Detailed instructions for flush mounting the device, including drilling and cutting.

Connection Considerations

Information regarding cable connections and securing them to the device.

Connecting the Wiring Harness to Power

Procedure for connecting the device's power wiring harness to the power source.

NMEA 2000 Considerations

Guidelines for connecting the device to an NMEA 2000 network.

Composite Video Considerations

Information on connecting composite video sources to the device's CVBS IN port.

Accessing and Customizing RV Builder Settings

Steps to access RV Builder settings and customize device configurations.

Customizing the Startup Screen

Instructions on setting a custom image for the device's startup screen.

Customizing the Home Page

Steps to customize the device's home page layout and add/edit items.

Customizing the Home Page Background

Instructions on setting a custom background image for the device's home page.

Adding and Editing Digital Switching Pages

Guide to adding and customizing digital switching pages for compatible systems.

Troubleshooting Device Power Issues

Guidance on resolving issues where the device will not turn on or turns off unexpectedly.

Device Specifications

Technical specifications for the device, including dimensions, power, and memory.

Garmin RV Specifications

General

Brand	Garmin
Model	RV
Category	Monitor
Language	English