GE Profile 22 - Page 57

57
SafetyInstructions OperatingInstructions InstallationInstructions TroubleshootingTips ConsumerSupport
PerformanceDataSheet
SmartWaterFiltrationSystem
MWFCartridge
This system has been tested according to NSF/ANSI 42/53 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to
a concentration less than or equal to the permissible limit for water leaving the system, as specied in NSF/ANSI 42/53.*
(100% safety factors built in for unmetered usage)
Standard No. 42: Aesthetic Eects
Parameter
USEPA
MCL
Inuent
Challenge Concentration
Inuent
Average
Euent % Reduction
Min. Required
Reduction
Average Maximum Average Maximum
Chlorine - 2,0 mg/L +10% 1,96 mg/L 0,06 mg/L 0,11 mg/L 96,77% 94,74% > 50%
T & O - - - - - - - -
Particulate** - at least 10.000 particles/mL 6.400.000 #/mL 58.833 #/mL 150.000 #/mL 99,14% 97,97% > 85%
Standard No. 53: Health Eects
Parameter
USEPA
MCL
Inuent Challenge
Concentration
Inuent
Average
Euent % de reducción
Min. Required
Reduction
Average Maximum Average Maximum
Turbidity 1 NTU 11 +1 NTU*** 10,5 NTU 0,14 NTU 0,28 NTU 98,54% 97,20% 0,5 NTU
Cysts
99,95%
Reduction
Minimum 50.000 L 118.750 #/L < 1 #/L 4 #/L > 99,99% > 99,99% > 99,95%
Asbestos
99%
Reduction
107–108bras/L;
> 10µm
57 MF/L 0,996 MF/L < 1 MF/L 99,60% 99,39% > 99%
Lead at pH 6.5 0,015 mg/L 0,15 mg/L +10% 0,1567 mg/L < 0,001 mg/L < 0,001 mg/L 99,36% 99,29% 0,010 mg/L
Lead at pH 8.5 0,015 mg/L 0,15 mg/L +10% 0,1433 mg/L < 0,001 mg/L < 0,001 mg/L 99,30% 99,29% 0,010 mg/L
Mercury at
pH 6.5
0,002 mg/L 0,006 mg/L +10% 0,0059 mg/L 0,000350 mg/L 0,0007 mg/L 94,70% 87,50% 0,002 mg/L
Mercury at
pH 8.5
0,002 mg/L 0,006 mg/L +10% 0,0057 mg/L 0,000325 mg/L 0,0006 mg/L 93,20% 89,29% 0,002 mg/L
Alachlor 0,002 mg/L 0,04 mg/L +10% 0,0367 mg/L 0,00023 mg/L 0,0004 mg/L 99,34% 98,67% 0,002 mg/L
Lindane 0,0002 mg/L 0,002 mg/L +10% 0,0020 mg/L < 0,00002 mg/L < 0,00002 mg/L 99,00% 98,95% 0,0002 mg/L
2,4-D 0,070 mg/L 0,210 mg/L +10% 0,2033 mg/L 0,00337 mg/L 0,011000 mg/L 98,32% 94,50% 0,070 mg/L
Toxaphene 0,003 mg/L 0,015 mg/L +10% 0,0160 mg/L 0,00100 mg/L 0,001000 mg/L 93,44% 91,67% 0,003 mg/L
Benzene 0,001 mg/L 0,015 mg/L +10% 0,0145 mg/L 0,000500 mg/L 0,000500 mg/L 96,51% 95,83% 0,005 mg/L
Carbofuran 0,040 mg/L 0,080 mg/L +10% 0,0830 mg/L 0,001000 mg/L
0,001000 mg/L 98,78% 98,65% 0,04 mg/L
1,4
dichlorobenzene
0,075 mg/L 0,225 mg/L +10% 0,2283 mg/L 0,000500 mg/L 0,000500 mg/L 99,78% 99,77% 0,075 mg/L
Atrazine 0,003 mg/L 0,009 mg/L +10% 0,0087 mg/L < 0,0005 mg/L < 0,0005 mg/L 94,22% 93,33% 0,003 mg/L
* Tested using a ow rate of 0.50 gpm; pressure of 60 psi; pH of 7.5 ±0.5; temp. of 68°±5°F (20°±3°C).
** Measurement in Particles/ml. Particles used were 0.5-1 microns.
*** NTU=Nephelometric Turbidity units.
OperatingSpecications
• Capacity: certied for up to 300 gallons (1135 l); up to six months for models without a replacement lter indicator light; up to one year for models with a replacement lter indicator light.
• Pressure requirement: 40–120 psi (2.8–8.2 bar), non-shock.
• Temperature: 33–100ºF (0.6–38ºC).
• Flow rate: 0.5 gpm (1.9 lpm).
GeneralInstallation/Operation/MaintenanceRequirements
• Flush new cartridge at full ow for 3 minutes to purge out trapped air.
• Replace cartridge when ow becomes too slow.
SpecialNotices
• Installation instructions, parts and service availability, and standard warranty are included with the product when shipped.
• This drinking water system must be maintained according to manufacturer’s instructions, including replacement of lter cartridges.
• Do not use with water that is micro biologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certied for cyst reduction may be used on
disinfected water that may contain lterable cysts.
• The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your water.
• Check for compliance with the state and local laws and regulations.
• Note that while the testing was performed under standard laboratory conditions, actual performance may vary. Systems must be installed and operated in accordance with manufacturer
recommended procedures and guidelines.