ge.com
COOLMODE
RemoteControl
l. Px_ss COOLpad.
2. Px_ss LOW.IVIEDor HIpads to set desired fire speed.
3. PI_SS the INCREASEA/DECREASEVpads to set the
desix_d temperature 60°F to 85°F in l °F increments.
ControlPanel
l. Pxess fl_e MODEpad until tile COOLindicator lig]lt is
lit and the LOW.MEDor Hlin(ficator light is lit tbr
die (lesix_(1t_m speed.
2. Px>ss the INCREASEA/DECRFAISET pads to set the
(Iesix_d temperature 60°F to 85°F in l °F increments.
A them_osmt is used to maint_fin the room
tempenmtre. Tile compressor will wcle on and off
to keep tile room at the set level of comtbrt. Set die
thermostat at a lower number and die indoor air will
become coolex; Set tile thermostat at a higher nmnber
and the indoor air will become _mnex:
NOTE:ff theairconditionerisoffandisthenturnedon
whilesettoCOOL,it willtakeapproximately3minutesfor
thecompressortostartandcoolingtobegin.
CoolingDescriptions
ForNormalCooling--Select the COOLmode and
HIGHor MEDtim with a middle set temperature.
ForMaximum Cooling--Select tile COOLmode
and HIGHtim with a lower set tempemtm>.
ForQuieter&NighttimeCooling--Selectthe COOLmode
and LOWfimwidi a middle set temperature.
NOTE:If youswitchfroma COOLsettingtoOFFor to
afansetting,waitatleast3minutesbeforeswitchingback
toaCOOLsetting.
Fan Switch
The tim switch is located behind the ti'()nt grille on the
control box. Access through a hole in control box.
_,_]mn set at CYCLE(do_n) the tbn e',cles on and ottl
When set at CONT(confimtous, tip) the tim runs all the
time providing a mi/x_ balanced mmperau/x_. The unit
is shipped in the CONrsetting.
FAN MODE
Use the FANmode to provide _dr circulation and
filtering without cooling. Since fire only settings do not
provkle cooling, a temperature setting will not be
displa}ed.
RemoteControl
Px>ss FAN pad. Press LOW,MEDor HI pads to set
(lesix_(1 fire speed.
ControlPanel
Pxess die MODEpad until the FANindicator light is lit
and the LOW, MEDor HIin(ficator light is lit for the
(lesix_(1 f_mspeed.
Vent Control
The vent control is located behind the ti'ont grille on
the right side of the air (fischarge area. "_\lmn set at
CLOSE,only tile air inside fl_e room will be circulated
and conditioned. When set at OPEN,some inside air is
exhausted outside.
To opeil or close tile vent:
1. Remove the ti'ont grille.
2. Remo\ e the vent card scx_.
3. Remove vent card, turn it over and replace it b}
locating rear hole in card over locating pin inside air
discharge and reattaching scre_ at fi'ont.
Theunitleavesthe factoryset attheCLOSEposition.
._Locating hole
Screwhole "_.
OPENposition
(Meshendtowardback)
Screwho
CLOSEposition
(Meshendtowardfront)
A# Direction
Hofizont_fl lomers
on fl_e Ii'ont grille let
you control the air
(lirection up and
douvI/.
Remove tile fi'ont
grille to a@/st the
vertical lou\'ers
side-to_ide to
dixect the air
left or fight.
To Next Page
Loading...
