GE D30 series - Wiring; Typical Wiring

636 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

GE Multilin D30 Line Distance Protection System 3-9

3 HARDWARE 3.2 WIRING

3

3.2WIRING 3.2.1 TYPICAL WIRING

Figure 3–12: TYPICAL WIRING DIAGRAM

Table of Contents

Default Chapter3
- Table of Contents3
1 Getting Started11
- Important Procedures11
  - Cautions and Warnings11
  - Inspection Checklist11
- Ur Overview12
- Enervista Ur Setup Software15
- Ur Hardware26
- Using the Relay27
2 Product Description31
- Introduction31
- Specifications39
3 Hardware51
- Description51
- Wiring59
- Direct Input/Output Communications75
4 Human Interfaces91
- Enervista Ur Setup Software Interface91
- Extended Enervista Ur Setup Features94
- Faceplate Interface103
5 Settings117
- Overview121
- Product Setup128
- System Setup198
- Flexlogic217
- Grouped Elements239
- Control Elements302
- Inputs and Outputs336
- Transducer Inputs and Outputs353
- Testing359
6 Actual Values363
- Overview363
  - Actual Values Main Menu363
- Status363
- Records382
- Product Information384
  - Model Information384
  - Firmware Revisions384
7 Commands and385
- Commands385
8 Security397
- User Accounts397
- Cybersentry400
  - Overview400
  - Security Menu402
9 Theory of Operation407
- Distance Elements407
- Phase Distance Applied to Power Transformers Description417
  - Example420
- Ground Directional Overcurrent422
  - Example422
  - Description422
- Fault Locator427
  - Fault Type Determination427
10 Application of431
- Application Guidelines431
Settings 10.1.1 Introduction431
- Impact of Memory Polarization431
- High Set Overcurrent Elements431
- Distance Elements (Stepped Distance Scheme)432
  - Phase Distance432
  - Ground Distance433
- Series Compensated Lines436
- Phase Distance through Power Transformers438
  - Phase Distance Protection438
  - Example439
Parameter Lists441
- Flexanalog Items441
- A.1.1 Flexanalog Items441
- Flexinteger Items450
- A.1.2 Flexinteger Items450
Modbus Communications451
Modbus Rtu Protocol451
- Introduction451
- Physical Layer451
- Data Link Layer451
- B.1.1 Introduction451
- Algorithm452
- B.1.4 Crc-16 Algorithm452
Modbus Function Codes453
- Supported Function Codes453
- Read Actual Values or Settings (Function Code 03/04H453
- Execute Operation (Function Code 05H454
- Store Single Setting (Function Code 06H454
- Store Multiple Settings (Function Code 10H455
- Exception Responses455
File Transfers456
- Obtaining Relay Files Via Modbus456
- Modbus Password Operation458
Memory Mapping459
- Modbus Memory Map459
- Data Formats519
- B.4.2 Data Formats519
Iec 61850557
Overview557
- Introduction557
- Communication Profiles557
- C.1.1 Introduction557
Server Data Organization558
- Overview558
- Ggio1: Digital Status Values558
- Ggio2: Digital Control Values558
- Ggio4: Generic Analog Measured Values558
- C.2.1 Overview558
- Mmxu: Analog Measured Values559
- Protection and Other Logical Nodes559
Server Features and Configuration561
- Buffered/Unbuffered Reporting561
- File Transfer561
- Timestamps and Scanning561
- Logical Device Name561
- Location561
- Logical Node Name Prefixes562
- Connection Timing562
- Non-Iec 61850 Data562
- Communication Software Utilities562
Generic Substation Event Services: Gsse and Goose563
- Overview563
- Gsse Configuration563
- Fixed Goose563
- Configurable Goose563
- C.4.1 Overview563
- Ethernet Mac Address for Gsse/Goose566
- Gsse ID and Goose ID Settings566
Iec 61850 Implementation Via Enervista Ur Setup567
- Overview567
- C.5.1 Overview567
- Configuring Iec 61850 Settings568
- About ICD Files569
- Creating an ICD File with Enervista Ur Setup573
- About Scd Files573
- Importing an Scd File with Enervista Ur Setup576
Acsi Conformance578
- Acsi Basic Conformance Statement578
- Acsi Models Conformance Statement578
- Acsi Services Conformance Statement579
Logical Nodes582
- Logical Nodes Table582
Iec 60870-5-104587
Iec 60870-5-104 Protocol587
- Interoperability587
- D.1.1 Interoperability587
- Point List595
- D.1.2 Point List595
- Dnp V3.00 Device Profile597
- E.1.2 Implementation Table600
Dnp Point Lists604
- Binary Input Points604
- Binary and Control Relay Output605
- Counters606
- E.2.3 Counters606
- Analog Inputs607
- E.2.4 Analog Inputs607
Change Notes609
- Revision History609
- F.1.1 Revision History609
- Changes to the Manual610
Abbreviations621
- Standard Abbreviations621
  - F.2.1 Standard Abbreviations621
  - F.3.1 Ge Multilin Warranty625
Warranty626

Related product manuals

Preview: GE D60

Preview: GE D30

Preview: GE 850

Preview: GE 869

Preview: GE C70

Preview: GE 350

Preview: GE 845

Preview: GE G60

Preview: GE 339

Preview: GE MI-869

Preview: GE Multilin 850

GE Multilin 850

Preview: GE Multilin 3 Series

GE Multilin 3 Series