GE Digital Energy SitePro 10 kVA User Manual

GE Digital Energy
Power Quality
S
P
_
0
1
0
-
0
4
0
_
S
8
_
U
P
S
_
G
E
_
0
1
Operating Manual
Uninterruptible Power supply
Digital Energy™
SitePro
10 – 15 – 20 – 30 – 40 kVA
400 Vac CE / Series 8
GE Consumer & Industrial SA
General Electric Company
CH – 6595 Riazzino (Locarno)
Switzerland
T +41 (0)91 / 850 51 51
F +41 (0)91 / 850 51 44
www.gedigitalenergy.com
GE imagination at work

GE Digital Energy SitePro 10 kVA Specifications

General

Brand	GE
Model	Digital Energy SitePro 10 kVA
Category	UPS
Language	English

Summary

1 SAFETY RULES

General Safety Guidelines

General handling, safety, and precautions for the UPS.

Installation Safety Requirements

Safety requirements and warnings for UPS installation.

Storage and Battery Safety

Guidelines for safe storage and handling of the UPS and batteries.

Safety Symbols and Warnings Explained

4.2 OPERATION MODES

Normal Operation Mode (VFI)

Description of the standard Voltage Frequency Independent operation mode.

Super Eco Mode (SEM)

Mains Failure and Recovery Operation

How the UPS operates during mains power failure and recovery.

Automatic and Manual Bypass Operation

Functionality and use of automatic and manual bypass systems.

4.3 PARALLEL SYSTEM OPERATION

Introduction to Parallel Systems

RPA Parallel System Features

System Control, Synchronization, and Load Sharing

4.4 Rectifiers Parallel on Same Battery

4.5 Service and Technical Support

5 INSTALLATION

5.4 Place of Installation and UPS Location

5.5 Ventilation and Cooling Requirements

5.7 ELECTRICAL WIRING

5.7.1 Mains Input Connection

How to connect the UPS to the mains power supply.

5.7.2 Input/Output Protection and Wire Sizing

Guidance on overcurrent protection and cable sizing for UPS.

5.7.3 Installation Requirements Examples

5.8 ELECTRICAL CONNECTION

5.8.1 Power Connections Overview

Terminal connections for power input, output, and battery.

5.8.2 Choosing AC Input for Power Supply

5.9 RPA Parallel System Connection

5.9.1 Power Wiring for Parallel Units

5.9.2 Parallel Control Bus Connection

5.9.3 Control Bus Cable Location and Routing

6 CONTROL PANEL

7 LCD SCREEN

7.2 Metering Functionality

7.3 Alarm Display and Navigation

7.3.1 Events, Alarms, and Messages List

7.3.2 Alarm Codes and Meanings

7.4 SETUP

7.5 COMMANDS

Executing UPS Operational Commands

8 OPERATION

8.1 Procedures for Single SitePro UPS

Step-by-step instructions for operating a single SitePro UPS.

8.1.1 Initial Start-up of a Single SitePro UPS

Step-by-step guide for the initial power-up of a single UPS.

UPS Configuration During Start-up

Setting essential configuration parameters during the initial UPS start-up.

Battery Configuration Settings

Single UPS Start-up Procedure Steps

Detailed steps to start up a single SitePro UPS unit.

8.1.2 Shutdown with Load Transfer to Manual Bypass

Procedure for safely shutting down a single UPS with load transfer.

8.1.3 Restoring Normal VFI Function from Manual Bypass

Steps to return the UPS to normal VFI operation from manual bypass.

8.1.4 Complete UPS Shutdown Procedure

Steps for a full power-down of the UPS system.

8.1.5 Restoring Normal Operation After 'Load Off'

How to resume normal operation after activating the "Load Off" command.

8.2 Procedures for SitePro Parallel System

Instructions for operating SitePro UPS units in a parallel system.

8.2.1 Parallel System Initial Start-up

Step-by-step guide for powering up a SitePro parallel UPS system.

8.2.2 Parallel UPS Shutdown with Manual Bypass Transfer

Procedure for shutting down a parallel UPS system via manual bypass.

8.2.3 Restoring Parallel VFI Function from Manual Bypass

Steps to return a parallel system to normal VFI operation from bypass.

8.2.4 Separating a UPS Unit from a Parallel System

8.2.5 Reconnecting a UPS Unit to a Parallel System

8.2.6 Complete Parallel System Shutdown

Procedure for a full power-down of the entire parallel UPS system.

8.2.7 Restoring Parallel Operation After 'Load Off'

How to resume normal operation for a parallel system after "Load Off".

9 CUSTOMER INTERFACE

9.1.5 EPO (Emergency Power Off) Function

How to connect and use the Emergency Power Off function.

11 MAINTENANCE

11.1 Preventive Maintenance Overview

General guidelines and recommendations for UPS preventive maintenance.

11.1.1 Service Check and Cleaning

11.1.3 Component Replacement Guidelines

11.1.4 Battery Maintenance and Testing

Guidelines for battery testing, charging, and maintenance.

11.1.6 Preventive Maintenance Program Schedule

Detailed checklist for a comprehensive preventive maintenance program.