GE GFDN110EL0WW User Manual

Installation
Instructions
Electric Drger
09
Questions or Installation? Call: 1-800-GECARES (US)
or Visit our Web site at: www.GEApplionces.com (US)
PEDESTALS FOR DRYERS
(comes with individual installation instructions)
Three models available: - SBSD227F
- SBSDIO7H - SBSD137H
BEFOREYOU BEGIN
Read these instructions completelg and carefullg.
•IMPORTANT-savetheseinstructionsforlocal
inspector's use.
• IMPORTANT- Observea,governing codesand
ordinances.
• Note to Installer - Besure to leave these instructions with
the customer.
• Note to Customer- Keepthese instructions with your Use
and Care Book for future reference.
• Before the old dryer is removed from service or discarded,
remove the dryer door.
• Service information and the wiring diagram are located in
the control console.
• Do not allow children on or in the appliance. Close super-
vision of children is necessary when the appliance is used
near children.
• Install the dryer where the temperature is above 50°F for
satisfactory operation of the dryer control system.
WA ! G- RISKOFFIRE
• To reduce the risk of severe injury or death, follow all installation instructions.
• Clothes dryer installation must be performed by a qualified installer.
• Install the clothes dryer according to these instructions and in accordance
with local codes.
• This dryer must be exhausted to the outdoors.
• Use only 4" rigid metal ducting for exhausting the clothes dryer to the
outdoors.
• DO NOTinstall a clothes dryer with flexible plastic ducting materials.
If flexible metal (semi-rigid or foil-type) duct is installed, it must be UL listed
and installed in accordance with the instructions found in "Connecting The
Dryer To House Vent" on page S of this manual. Flexible venting materials
are known to collapse, be easily crushed, and trap lint. These conditions will
obstruct dryer airflow and increase the risk of fire.
• Do not install or store this appliance in any location where it could be
exposed to water and or weather.
• Save these instructions. (Installers: Besure to leave these instructions with
the customer).
NOTE: Installation and service of this drger
requires basic mechanical and electrical skills.
It is your responsibilitg to contact a qualified
installer to make the electrical connections.
TOOLS YOU
WILL NEED
SLIPJOINT PLIERS
FLAT BLADESCREWDRIVER
PHILLIPSSCREWDRIVER
4" DIA METALDUCT
(RECOMMENDED)
)
4" DIA FLEXIBLEMETAL(SEMI-RIGID)
ULLISTEDTRANSITIONDUCT
(IFNEEDED)
KITWXOSX10077(INCLUDES2 ELBOWS)
4"DIA FLEXIBLEMETAL(FOILTYPE)
ULLISTEDTRANSITIONDUCT
(IFNEEDED.)
MATERIALS YOU WILL NEED
/4"DUCT
CLAMPS(2)
OR
/4"SPRING
CLAMPS(2)
%
4"DIA,METAL
ELBOW
DUCTTAPE
EXHAUST SAFETY
HOOD GLASSES
GLOVES
3/4" STRAIN
RELIEF
ULRECOGNIZED
DRYERPOWERCORD
KIT(NOTPROVIDED
WITH DRYER)
ULRATED
120/240V,30A
WITH 3 OR4 PRONGS.
IDENTIFYTHEPLUG
TYPEASPERTHE
HOUSERECEPTACLE
BEFOREPURCHASING
LINECORD.
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Prepare the Area and Exhaust for Installation of New
Dryer (see section 1).
Check and Ensure the Existing External Exhaust is
Clean (see section 1) and Meets Attached Installation
Specifications (see section 3).
Remove the Foam Shipping Pads (see section 1).
Move the Dryer to the Desired Location.
Connect the Power Supply (see section 2).
Connect the External Exhaust (see section 4).
Level Your Dryer (see section 5).
Step 8
Step 9
Check the Operation of the Power Supply and
Venting.
Place the Owners Manual and the Installation
Instructions in a Location Where They Will Be
Noticed By the Owner.
For Alcove or Closet Installation, see section 6.
For Bathroom or Bedroom Installation, see section 7.
For Mobile or Manufactured Home see, section 8.
For side or bottom exhaust, see section 9.
500A436PO09 RevO Pub # 31-16228

GE GFDN110EL0WW Specifications

General

Brand	GE
Model	GFDN110EL0WW
Type	Electric Dryer
Color	White
Voltage	240 V
Amperage	30 A
Drum Material	Aluminized Alloy
Number of Cycles	12
Number of Temperature Settings	4
Wrinkle Care Option	Yes
Moisture Sensor	Yes
Energy Star Certified	No
Ventless	No
Width	27 in

Summary

Installation Instructions

Customer Support

Contact GE for installation questions via phone or website.

Pedestals for Dryers

Lists available pedestal models and notes individual instructions.

Pre-Installation Checklist

Essential steps and notes for installers and customers before installation.

Tools Required for Installation

Lists common tools needed for dryer installation.

Materials Required for Installation

Lists necessary materials for dryer installation.

Fire Risk Warning

Crucial safety warnings regarding fire hazards during installation.

Clearance Requirements

Specifies minimum clearances for non-alcove/closet installations.

Preparing for Dryer Installation

Tips for installation sequence and removing shipping pads.

Cleaning Wall Exhaust Opening

Instructions for cleaning the wall exhaust opening and checking damper.

Electrical Connection Information

Important electrical safety warnings and requirements.

Electrical Requirements

Details the specific electrical circuit requirements for the dryer.

Grounding Instructions

Guidance on proper grounding methods for the dryer.

4-Wire Connection

Instructions for connecting the dryer using a 4-wire electrical connection.

3-Wire Connection

Steps for connecting the dryer using a 3-wire electrical connection.

Exhaust Information and Warnings

Critical warnings and guidelines for dryer exhaust systems to prevent fire.

Exhaust Length Guidelines

Table detailing maximum exhaust lengths based on duct type and bends.

Exhaust System Checklist

Key points to check for proper exhaust installation and maintenance.

Exhaust Hood/Wallcap Requirements

Specifications for exhaust hoods and wallcaps to ensure proper airflow.

Exhaust System Details

Guidelines for exhaust turns, sealing, and insulation.

Exhaust Connection Warnings

Further warnings about fire and injury risks related to exhaust connections.

Standard Rear Exhaust (Floor Level)

Diagram and instructions for rear exhaust venting at floor level.

Standard Rear Exhaust (Above Floor)

Diagram and instructions for rear exhaust venting above floor level.

Leveling and Stabilizing the Dryer

Steps to properly level the dryer using its adjustable legs.

Connecting to House Vent

Detailed instructions for connecting the dryer to the house exhaust system.

Rigid Metal Transition Duct

Recommendation for using rigid metal ducts for best performance.

UL-Listed Flexible Metal (Semi-Rigid) Duct

Guidelines for using semi-rigid flexible metal transition ducts.

UL-Listed Flexible Metal (Foil-Type) Duct

Guidelines for using foil-type flexible metal transition ducts.

Alcove or Closet Installation

Specific clearance and ventilation requirements for alcove/closet installations.

Bathroom or Bedroom Installation

Notes on installing the dryer in bathrooms or bedrooms, referencing codes.

Mobile/Manufactured Home Installation

Requirements for installing dryers in mobile or manufactured homes.

Side or Bottom Cabinet Exhaust

Instructions for venting the dryer from the side or bottom of the cabinet.

Adding New Ductwork

Steps for adding or modifying ductwork for side exhaust.

Adding Elbow for Side Exhaust

Detailed steps for adding an elbow and duct for side exhaust.

Adding Elbow for Bottom Exhaust

Steps for adding an elbow and duct for bottom exhaust.

Adding Rear Cover Plate

Instructions for adding a cover plate to the rear of the cabinet after exhaust modification.

Dryer Registration

Information on how to register the dryer for warranty and support.

Door Reversal Parts

Lists parts required for reversing the dryer door swing.

Removing the Door Assembly

Step-by-step guide to removing the dryer door from the cabinet.

Removing the Hinge Assembly

Instructions for removing the hinge assembly from the door.

Reinstalling the Hinge Assembly

Steps to reinstall the hinge assembly on the opposite side of the door.

Reinstalling Nuts and Hinge Cover

Instructions for reattaching nuts and the hinge cover to the door.

Reassembling the Door Assembly

Steps to reassemble the dryer door after reversing the swing.

Moving the Strike Bracket

Instructions for moving the strike bracket to the opposite side for door reversal.

Servicing Precautions

Important safety warnings and notes regarding servicing the dryer.

Rough-in Dimensions