GE GFWN1300 User Manual (English)

Questions and Answers:

L
lopezannSep 4, 2025
Why are there snags, holes, tears, or excessive wear on my clothes after washing in my GE GFWN1300 Washer?
- M
  Mary NorrisSep 4, 2025
  Snags, holes, tears, or excessive wear on clothes after washing in your GE washer can be due to: * Overloading: Do not exceed maximum recommended load sizes. * Objects left in pockets: Remove loose items from pockets, such as pens, pencils, nails, or screws. * Unfastened items: Fasten snaps, hooks, buttons, and zippers. Remove sharp objects left in pockets.
T
turnerjasonSep 2, 2025
Why does water not enter my GE GFWN1300, or enters slowly?
- J
  Jennifer BullockSep 2, 2025
  If water isn't entering your GE washer or is entering slowly, it could be due to a few reasons. The washer performs system checks after the Start button is pressed. Ensure that both the hot and cold water faucets are fully turned on. The water valve screens or inlet hose screen washers might be clogged; turn off the water source and remove the water connection hoses from the upper back of the washer or remove the inlet hoses from the wall faucets to inspect and clean them. Improper sorting, overloading or incorrect wash cycle can also be the causes. Load your washer so clothes have enough room to move freely and match cycle selection to the type of fabric you are washing.
M
Mason WilliamsonAug 25, 2025
What to do if my GE GFWN1300 Washer is not draining, spinning, or tumbling?
- A
  Anita GainesAug 25, 2025
  If your GE washer isn't draining, spinning, or tumbling, it could be due to several reasons. First, the load might be out of balance; try redistributing the clothes and running a Drain + Spin or Rinse + Spin cycle. If you're washing a small load with heavy and light items, increase the load size. Another cause might be a clogged pump, or the drain hose could be kinked or improperly connected, so straighten the drain hose ensuring the washer isn't sitting on it. Also, the household drain may be clogged, requiring you to check your plumbing or call a plumber. Lastly, ensure there's an air gap between the hose and drain to prevent siphoning.
A
andradehaleyAug 31, 2025
Why is my GE GFWN1300 Washer leaking water?
- J
  johnnyalvarezAug 31, 2025
  If your GE washer is leaking water, several factors could be the cause. Check the door gasket to ensure it's properly seated and not torn. If water is present on the back left of the washer, it indicates an oversudsing condition, suggesting you should use less detergent. Inspect the fill and drain hoses to confirm they are tightly connected at both the washer and the faucets, and that the drain hose is correctly inserted and secured to the drain. A clogged household drain could also be the culprit. The dispenser might be clogged, especially if you're using powder soap; remove the drawer and clean both it and the inside of the dispenser box. Make sure that you are using only HE detergent in the correct amount. Finally, if it's a new installation, check the dispenser box for any cracks.
N
Nathaniel BrooksAug 30, 2025
How to fix improper dispensing of softener or bleach in my GE GFWN1300?
- K
  Kathy ChapmanAug 30, 2025
  If your GE Washer is not dispensing softener or bleach properly, regularly clean the dispenser drawer to remove chemical buildup. Ensure you're using the correct amount of softener or bleach and not filling above the max line. Also, make sure the softener and bleach caps for the dispenser are properly seated; otherwise, they won't work correctly.
H
heatherlewisAug 29, 2025
Why does water not enter my GE Washer or enters slowly?
- J
  Jamie TaylorAug 30, 2025
  If water does not enter your GE Washer or enters slowly, it could be due to several reasons. First, after pressing Start, the washer performs system checks, and water will flow 60 seconds after Start is pressed. Ensure both hot and cold water faucets are fully turned on. Check the water valve screens and inlet hose screen washers for blockages; turn off the water source and remove the hoses to clean the screens. Other potential causes include improper sorting, overloading the washer, or selecting the incorrect wash cycle.
P
Pamela McdanielAug 29, 2025
Why is my GE GFWN1300 Washer improperly dispensing softener or bleach?
- B
  Bryan GonzalesAug 29, 2025
  If your GE Washer is not dispensing softener or bleach properly, it may be because: * The dispenser is clogged. Clean the dispenser drawer monthly to remove any buildup of chemicals. * The softener or bleach is filled above the max line. Make sure you are using the correct amount of softener or bleach.
N
Nathan ClarkAug 28, 2025
Why is water not entering my GE Washer, or entering slowly?
- A
  angelahoodAug 28, 2025
  If water isn't entering your GE Washer or is entering slowly, consider these possibilities: * The washer performs automatic system checks after the Start button is pressed. Water will flow 60 seconds after Start is pressed. * Make sure both the hot and cold water faucets are fully turned on. * The water valve screens may be clogged. Turn off the water source, remove the water connection hoses from the back of the washer, and clean the screens with a brush or toothpick. Then, reconnect the hoses and turn the water back on. * The inlet hose screen washers may be clogged. Turn off the water source, remove the inlet hoses from the wall faucets, and clean the screen washers in the end of the hoses with a brush or toothpick. Reconnect the hoses and turn the water back on.
S
Steven MullenAug 27, 2025
Why is my GE GFWN1300 not dispensing softener or bleach correctly?
- A
  Alice AndersonAug 28, 2025
  If your GE Washer is not dispensing softener or bleach properly, clean the dispenser drawer monthly to remove any buildup of chemicals. Make sure you are using the correct amount of softener or bleach, and ensure the softener and bleach caps for the dispenser are seated correctly.
A
Ashley WrightAug 27, 2025
Why is water not entering my GE Washer?
- K
  Katherine KlineAug 27, 2025
  If water isn't entering your GE Washer or is entering slowly, several factors could be at play. After you press Start, the washer performs system checks, and water should flow within 60 seconds. Ensure both hot and cold water faucets are fully turned on. Check the water valve screens and inlet hose screen washers for blockages; turn off the water source, disconnect the hoses, clean the screens, and then reconnect the hoses.

GE GFWN1300 Specifications

General

Color	White
Control Type	Electronic
Steam Function	Yes
Energy Star Certified	Yes
Washer Type	Front Load
Capacity	2.4 cu. ft.
Height	33.25 in
Wash Cycles	Active Wear, Delicates, Normal, Quick Wash