EasyManuals Logo

GE LED Puck Lights User Manual

GE LED Puck Lights
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
CABINET
COUNTER TOP
WALL
Thank you for your purchase!
Instructions
made easy
Exclusive deals
Read instructions or watch
easy-to-follow video. Scan code
or visit byjasco.com/54849i
For deals, to register your
purchase and to tell us how we’re
doing, simply scan the code or visit
byjasco.com/deals
Having problems?
Let us know how we can help. Call
1-800-654-8483 between
7AM-8PM, M-F, Central Time.
Like our product?
Leave a review on your
favorite retailer website
or amazon.com
INSTALLATION OPERATION
Carefully plan out your installation prior
to securing your lights to the mounting
surface, making sure that your 5ft. line cord
will reach the nearest electrical outlet.
For kitchen installations, the recommended
mounting surface is near the front lip
of your kitchen under cabinets. This will
provide the best light distribution across
a countertop.
STEP 1: CHOOSE INSTALL LOCATION
Before installing, select a suitable mounting
location that is dry and capable of
supporting the pucks. Make sure that there
is plenty of room for the included 5ft. power
cord to reach the nearest outlet.
DO NOT ATTEMPT TO INSTALL LED PUCK
LIGHTS WHILE PLUGGED IN.
STEP 2: MARK SCREW LOCATIONS
On either side of the puck are keyhole tabs.
Using these for guidance, hold the puck in
place and use a pencil to mark the location
for the screws.
STEP 3: PRE-DRILL HOLES
Using the pencil marks for guidance, pre-
drill holes in the mounting surface with a
1/16in. (1.5mm) drill bit for soft woods and
a 3/32in. (2.4mm) drill bit for hard woods.
STEP 4: INSERT SCREWS
Insert the screws with a #1 Phillips
screwdriver, leaving 1/8in. beyond
the surface.
STEP 5: MOUNT PUCKS
Align the keyhole tabs with the screws and
slide the puck into place. Tighten the screws
as needed.
.
STEP 6: CONNECT WITH LINKING CORDS
Insert the 3-pin connector on the power
cord into the xture and the at plug into
the nearest 120VAC 60Hz outlet.
STEP 7: PLUG IN TO POWER
The included power cord has a at plug on
one end and a 3-pin connection point on
the other. Plug the 3-pin connector into the
nearest puck in the sequence and the at
plug into a 120VAC 60Hz outlet.
LOW/OFF/HIGH SWITCH
Use the switch on the side of each LED puck
to change between OFF, low-level white
light and high-level white light. Each puck in
the sequence is independently controlled.
LINKING ADDITIONAL FIXTURES:
To add more light pucks (sold separately),
simply follow the steps above. Keep in
mind the distance between each puck
and not to exceed the maximum of 20 LED
light xtures per outlet. The sequence is
independently controlled.
MARK
PRE-DRILL
WARNINGS TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS:
This xture has a polarized plug (one blade is wider than the
other) to reduce the risk of electric shock. This plug will t into a
polarized outlet only one way. If the plug does not t fully in the
outlet, reverse the plug. If it still does not t, contact a qualied
electrician. Never use an extension cord unless the plug can be
fully inserted. Do not alter the plug.
• Read the entire installation procedure before
you begin.
Not to be used with a dimming circuit or any other
electronically switched control.
• Do not attempt to install the xture while plugged in.
• Save these instructions so you can refer to them at
a later time.
CLEANING INSTRUCTIONS: Your xture is made from quality
materials that will last for many years with minimum care.
When cleaning, make sure you have unplugged your xture
and allowed sucient time for the unit to cool to room
temperature. You should clean the housing and lens using a
soft, damp cloth. You should plug your xture back in only
after the xture has thoroughly dried.
LIGHTING SPECS FOR 3 PUCKS
LUMENS: 450 WATTAGE: 8.4
CRI: 94 LUMENS/WATT: 53.6
CCT: 3000K
LIGHTING SPECS FOR 5 PUCKS
LUMENS: 750 WATTAGE: 14
CRI: 94 LUMENS/WATT: 53.6
CCT: 3000K
LED Puck Lights
User Manual
See reverse for easy-to-follow
instructions and exclusive deals.
IMPORTANT:
BEFORE INSTALLING, READ ALL SAFETY INSTRUCTIONS
LISTED AT THE END OF THIS MANUAL.
ELECTRICAL CORD CAN BE ROUTED
AROUND CORNERS
TO SUIT THE INSTALLATION
3 PIN
3 PIN
3 PIN
2 PIN2 PIN
SWITCH
MOUNT
Discover more premium LED
lighting and lighting accessories
at byjasco.com/lighting
Low
Hi
Off

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the GE LED Puck Lights and is the answer not in the manual?

GE LED Puck Lights Specifications

General IconGeneral
BrandGE
ModelLED Puck Lights
CategoryLighting Equipment
LanguageEnglish

Related product manuals