9919-1012012-J Rev. 12-2019
www.geckoalliance.com
© Groupe Gecko Alliance Inc., 2019
All trademarks or registered trademarks are the property of their respective owners. Printed in Canada
Water temperature
The temperature shown at the top of the screen gives
the actual water temperature.
Use the Up and Down buttons to set the desired
temperature. The set point will appear in blue at
the bottom. After 3 seconds without any change to
the set temperature value, the keypad will resume the
normal display of messages.
Description
Main functions
Quick Reference Card
Please consult your spa user manual for complete info on the features of your spa system.
in
.k506
intuitive color keypad
The in.k506 is built with all the great features you've come to love
in the in.k800, but in a smaller package. It is discreet, compact,
and unobtrusively beautiful. Save space without losing out on function.
Settings
Light Key
Mode
Up
Key 1
Down
Selection lights Key 2
*Functions for keys 1 and 2 will depend on your system's low level configuration.
Start or stop accessories
To start or stop an accessory, press the associated
button. Icons will become animated when their
accessory is turned on, and inanimate when turned
off. Icons on the screen will reflect the speed or state
of the devices running on your spa.
When an accessory has more than two states,
press the button until it reaches the desired state.
Note (version 14.00 and higher): A special buttons
and icons mapping may be used when the spa
configuration has 4 accessories* (3 pumps and a
blower or 4 pumps and no blower). In this case only,
buttons and icons are divided in 2 sets of accessories.
Button #1 starts or stops pump #1 and pump #2.
Button #2 starts or stops Pump #3 and Pump #4/
blower. Corresponding icons will be animated when
one or more accessories are on.
* Only Pump #1 can have a dual speed.
Mode key
Successive presses on the Mode key will give access
to control different optional accessories of your spa
such as Audio and others. Note that if an accessory
is not present in your spa configuration, its menu will
not appear. Refer to the following section to get details
about the possible accessories and their detailed
functionalities. The screen will revert back to the spa
mode if no key is pressed for 60 seconds.
If you don't have any accessories, Mode key can be
used to change your display orientation
Settings key
One press gives you access to a menu to manage the
settings of your spa. Refer to the settings section for
details about the settings menu.
Main screen
The main screen gives you access to your accessories
and water temperature. At the bottom of the screen
you will see any error or maintenance messages that
are present.
Power
Press any button to turn the keypad on.
After 30 minutes without activity it will shut off.
5
After a few seconds the available networks will
appear on the screen, as well as their signal
strength.
Use the Up/Down keys to move through the list.
Select your network by pressing on Light key.
If the WiFi network is password protected enter it
when prompted.
• Use the arrow keys to choose your letters and
change the type of character (uppercase,
lowercase, number, symbol).
• Use Key 2 to move the curser forward
• Use Key 1 to backspace
• Use Light key to confim
If no password is required the in.touch will
connect automatically.
Once the in.touch module is connected to a WiFi
network a check mark in a green circle will appear
in the WiFi menu, and the network logo will
change to green in Settings menu.
Note: WiFi logo color in Settings menu
corresponds to the in.touch connection state.
Yellow = not connected
Green = connected to a network
Yellow with wait icon = connection attempt to a
network
Red with wait icon = in.touch no longer detected
(in.touch must be reset before next connection
attempt)
in.clear-200 / linked version
(version 13.00 and higher)
The in.k500 keypad can be used with the in.clear
sanitization system. The in.clear section allows
you to configure your maintenance settings and
Boost level.
For more information on maintenance and Boost
settings, see the in.clear user manual.
Use the Up and Down keys to make your
selection, then light key to confirm.
Use the Up and Down keys to change the
maintenance or Boost value, and light key
to confirm.
* If the maintenance value is modified by more than 2,
a warning message will appear with an option to cancel or
confirm the change.
Press on the Mode key to access your in.clear
module.
This menu allows you to activate or deactivate
your in.clear, to start or stop a Boost, and to enter
diagnostic mode.
Turning the in.clear on/off
Press the power key to turn the in.clear on or off.
Control the Boost level
Press on the Boost activation/deactivation key to
start a Boost, and again to cancel.
To adjust the Boost level use the arrow keys.*
A message indicating that Boost mode is active is
displayed at the bottom of the main screen for the
duration of the Boost.
* See the in.clear user manual for more details about Boost
levels.
Diagnostic Mode
Press on the Diagnostic key to start a
BromiCharge concentration level test. To exit
diagnostic mode press on the Diagnostic key
again. The system will automatically exit after
15 minutes.
In diagnostic mode, the BromiCharge gauge
indicates the approximate level of BromiCharge
in the spa water. Do not add BromiCharge if the
indicator is in the green zone.
When BromiCharge is added the indicator will
move slowly to the right. When water is added
to the spa the indicator will move to the left.
To obtain a good level of BromiCharge, start
the pumps and add the specified amount of
BromiCharge** and allow 5 minutes for the
indicator to adjust before adding more.
For optimal performance, aim for the middle of
the green zone.
** For more information on adjusting your BromiCharge level
see the in.clear user manual.
WIFI (version 7.00 and higher)
For the WiFi menu to appear in the Settings
menu your in.touch module must be equipped
with software version 11.00 or higher. This menu
allows you to connect your in.touch module to a
WiFi network or to change its network.
For more details about other in.touch connection
methods please see the in.touch techbook.
To connect your in.touch module to a wireless
network, use the Up/Down keys to go to the WiFi
option in the Settings menu and Light key to
select it.
in.clear
Wi-Fi (in.touch only)
in.mix
in.mix operation
This menu is only present if an in.mix system is
detected.
Press on the Mode key to access your in.mix.
By default, the in.mix selects Zone 1 when you
access the menu. After the first use, the menu will
automatically return to the last zone selected.
Zone selection
The zone selection keys allow you to select a zone to
modify its color.
• Press once to select the zone.
• Press a second time to deactivate the zone.
Changing colors
Once a zone is selected, use the arrow keys to
change the colors by moving up and down in the
color wheel.
Synchronizing zones
The synchronization/desynchronization key allows
you to match the color of the selected zone to the
other zones.
To Next Page
Need help?
General
