Gecko in.k800 Quick Reference Card

Settings key
One press gives you access to a menu to manage the
settings of your spa. Refer to the settings section for
details about the settings menu.
Mode key
Successive presses on the Mode key will give access
to control different optional accessories of your spa
such as Audio and others. Note that if an accessory
is not present in your spa configuration, its menu will
not appear. Refer to the following section to get details
about the possible accessories and their detailed
functionalities. The screen will revert back to the spa
mode if no key is pressed for 60 seconds.
Power
Press any button to turn the keypad on.
After 30 minutes without activity it will shut off.
Main screen
The main screen gives you access to your accessories
and water temperature. At the bottom of the screen
you will see any error or maintenance messages that
are present.
Notifications
A notification area at the top right-hand side of the
screen shows the state of certain accessories installed
in the spa.
Start or stop accessories
To start or stop an accessory, press the associated
button. Icons will become animated when their
accessory is turned on, and inanimate when turned
off. Icons on the screen will reflect the speed
or state of the devices running on your spa.
When an accessory has more than two states,
press the button until it reaches the desired state.
Water temperature
The temperature shown at the bottom of the screen
gives the actual water temperature. Use the Up and
Down buttons to set the desired temperature.
The set point will appear in blue. After 3 seconds
without any change to the set temperature value,
the current water temperature will reappear.
Description
Main functions
Quick Reference Card
Please consult your spa user manual for complete info on the features of your spa system.
in.k800
intuitive color keypad
With its bright, full color display, the in.k800 provides an intuitive
user experience, while its screen’s high resolution brings hot tub user
interfaces to a new level. Loaded with a large amount of memory and
a powerful on-board processor we have created the seamless
graphic interface that spa users have been waiting for.
Settings
Electrical configuration
Please do not make changes in this section
unless you are a qualified electrician.
In this section you can change the low-level
configuration, as well as modify the number of
phases and the entry current.
Use the Up/Down Keys to move to the selection
you want to modify. Use Key 2 to select, and the
Up/Down Keys to move through the selections.
Press Key 2 again to confirm. Please see the
techbook for your spa system for details on low-
level settings.
Once you have changed the number of phases
in the menu you will be unable to use the Up/
Down keys to return to the Low-level configuration
menu. Please go back and access the menu
again.
About
This section shows information about the in.k800
software number, and the revision numbers of the
different components of your system.
Standby
The Standby mode allows you to service your spa.
Pumps will stop for 30 minutes, and automatically
restart after this time.
Once Standby mode has been activated a screen
will appear to show that pumps are stopped.
The normal spa page will return at the end of
maintenance.
Press on the Confirm key to leave Standby mode
and restart the spa.
Error log
In this section you can see errors that have been
archived by the system. Use the Up and Down
keys to move through the list. Errors are archived
chronologically, from most recent to oldest (top to
bottom).
The Error log page shows the error code, the date
of the error, and the time.
To see more details on an error select it with key 2.
A screen will appear with more information on the
selected error.
For more information, see the Error messages
section in the in.k800 TechBook.
Since v16.00, to clear the Error log page, you have
to Factory Reset your keypad.
Date and time
Here you can adjust the time format, change the
year, date, and time. Use the arrows to choose
the setting that you want to adjust, and select it by
pressing key 2.
Use the arrow keys to change the parameters,
and key 2 to move between parameters. Key 1 will
take you back to the main Settings menu.
Keypad settings
In this section, you can change the temperature
unit, language, display orientation and rim light
color. Note the spa pack must be configured
accordingly to be able to change the rim light
color.
Use the arrow keys to choose the setting that you
want to adjust. Select it by pressing key 2 then
use the arrow keys again to change the setting.
When you change the display orientation, the
contextual options and arrow keys adjust to the
chosen orientation. The Mode and Menu keys
remain unchanged, as well as the accessory keys
in the main Spa menu.
* Functions for keys 1 to 5 will depend on
your system's low level configuration.
Settings
Key 2
Key 3
Key 1
Mode
(optional)
Up
Key 4
Key 5
Down
Selection lights Light/ Key 6
in.mix:
 •Indicatesthatanin.mixsystemisdetected.
in.clear:
 •Theiconisgreenwhenthein.clearis
generating bromine.
 •Theiconisgreywhenthein.clearisn't
generating bromine.
 •Aredcrossindicatesthatthein.clear
is turned off.
in.touch:
 •Indicatesthatthein.touchmoduleis
detected and connected to a Wi-Fi network.
 •Aredcrossindicatesthatthein.touch
  moduleisdetectedbutisn'tconnected
to a Wi-Fi network.
in.steam 2:
 •Theiconisgreenwhenthein.stream2isON.
 •Theiconisgreywhenthein.stream2isOFF.
For more information about the in.mix, in.clear,
in.touch or in.stream 2, refer to the Techbook.
in.mix
in.mix functions
This menu is only present if an in.mix system is
detected.
Press on the Mode key to access your in.mix.
By default, the in.mix selects Zone 1 when you
access the menu. After the first use the menu will
automatically return to the last zone selected.
Zone selection:
The zone selection keys allow you to select a zone
to modify its color.
•Pressoncetoselectthezone.
•Pressasecondtimetodeactivatethezone.
Changing colors:
Once a zone is selected use the arrow keys to
change the colors by moving up and down in the
color wheel.
Synchronizing zones:
The synchronization/desynchronization key allows
you to match the color of the selected zone to the
other zones.
9919-101201-F Rév. 01-2016
www.geckoalliance.com
© Groupe Gecko Alliance Inc., 2016 - Toutes les marques de commerce
ou marques déposées sont la propriété de leurs propriétaires respectifs.
Imprimé au Canada
8

Gecko in.k800 Specifications

General

Backlit Keys	Yes
Water Resistance	Yes
Display	LCD
Model	in.k800
Backlight	Yes
OS Compatibility	Windows, Linux, Mac