gefran 1300 Quick Start Guide

GEFRAN SpA
Via Sebina, 74 - 25050 PROVAGLIO D’ISEO (BS) ITALY
This Quick Start Guide provides basic information on
setting up the Gefran 1300 controller for the application
referenced above. Additional software and hardware
configuration information can be found in the User’s Manual
included with this controller or online at www.gefran.com
If needed, automatic tuning (Self-Tune) can be enabled
with the following steps
• Pressandhold
F

untilCFGappears
• Press
F

once,S.Tuappears—ENTER2
• Press
F

once
• Cyclepowertothecontroller
• LED3(
L3
)willflashduringthetuningprocess
Withthemachineatambienttemperatureand
thecontrolsetpoint(SV)set...
Self-TunewillautomaticallysavenewPID
valuesoncecomplete
Note
Change all menu parameters by
using the front panel buttons
GETTING STARTED
• Unpack Contents
• Verify model numberand application
• Power Controller
• Program for yourapplication
Program Your Gefran Controller
2
*Parametermaybeleftatdefaultvalueforinputtypes0...37
Input Sensor
Sensor Type Sensor Type
0 TCJ°C 30 PT100°C
1 TCJ°F 31 PT100°F
2 TCK°C 32 JPT100°C
3 TCK°F 33 JPT100°F
4 TCR°C 34 PTC°C
5 TCR°F 35 PTC°F
6 TCS°C 36 NTC°C
7 TCS°F 37 NTC°F
8 TCT°C 44 4...20mA
9 TCT°F 46 0...10V
Connect Your Controller
3
What’s Included
• 96x96 DIN 1300-RD00-00-0-x
Gefran Controller x2
• Mounting Bracket
• Panel Sealing Gasket
• Screw Terminal Cover x2
• Multi-Language Manual
1
• Pressandhold
F

untilPASappears—ENTER99
• Press
F

once,Proappears—ENTER128
• Press
F

once,PASappears—ENTER99
• Pressandhold
F

untilHrdappears
• Press
F

repeatedlyuntilbutappears—ENTER1
• Pressandhold
F

until1 nPappears
• Press
F

twice,tYPappears—ENTERtheInputSensornumber
 fromthelist
• Press
F

repeatedlyuntilLo.S*appears—ENTERtheminimumInputScalelimit
• Press
F

once,H i.S*appears—ENTERthemaximumInputScalelimit
• Press
F

repeatedlyuntilLo.L*appears—ENTERtheminimumAlarmScalelimit
• Press
F

once,H i.L*appears—ENTERthemaximumAlarmScalelimit
• Pressandhold
F

untilyoureturntothemainprocessdisplay.ThisisthedisplayafterPAS
andwillbeindicatedbytheProcessVariableifaninputsensorisconnected,orLo,H i,Sbr,
Errifnoinputisconnected.
• Usethe

and

buttonstoadjustthecontrolsetpoint(SV)fromthemaindisplay.
• Press
F

oncefromthemaindisplay,AL.1appearstoadjusttheAlarm1setpoint.
• Press the

buttontoswitchbetween automatic andmanualcontrol modes fromthe
maindisplay.LED1(
L1
)willlightwhileinmanualmode.
POWER
Additional wiring
configurations
are available
in the User’s
Manual and
General Setup
Guide
Quick Start Guide
1300-RD00-00-0-x Programmable PID Controller
2
-
1
+
7
8
11
10
6
-
5
+
ALARM
Heat & Alarm
HEATER
POWER CONTROL
THERMOCOUPLE
1 / 7

gefran 1300 Specifications

General

Brand	gefran
Model	1300
Category	Controller
Language	English