How to troubleshoot a fuel gauge that doesn't work on Gehl Front End Loaders?
If the fuel gauge on your Gehl Front End Loader isn't working, the issue could stem from a faulty fuel gauge sender, a faulty fuel gauge itself, or loose wiring/terminal connections. Replace the fuel gauge sender. Replace the fuel gauge. Verify wiring connections.
Why do high flow auxiliary functions slowly on my Gehl Front End Loader?
If the high flow auxiliary functions slowly on your Gehl Front End Loader, it could be due to control linkage misadjustment, low engine speed, low hydraulic oil level, or hydraulic oil viscosity that is too heavy. Check the linkage and readjust for full spool travel. Operate the engine at a higher speed. Add oil. Allow longer warming.
Why high flow auxiliary does not function on Gehl Front End Loaders?
If the high flow auxiliary on your Gehl Front End Loader does not function, it could be because the restraint bar is raised, the spool lock solenoid is malfunctioning, the restraint bar or seat switch is malfunctioning, the load sense signal line is loose or broken, the load sense compensation is not functioning, or the high pressure compensation on the pump is not functioning. Lower the restraint bar. Check the electrical connections to the lock solenoid and repair connections as needed. Check the load sense signal line; tighten or replace if necessary.
Why is the hydrostatic drive system noisy in my Gehl Front End Loader?
A noisy hydrostatic (drive) system in your Gehl Front End Loader can be attributed to a few potential issues: the hydraulic oil viscosity might be too heavy, there could be air in the hydraulic system, or the drive motor(s) or hydrostatic pump(s) might have internal damage or leakage. Allow longer warm-up or replace existing oil with the proper viscosity oil. Cycle lift and tilt cylinders to maximum stroke and maintain pressure for a short time to clear air from system. Also check for low oil level in reservoir, fill as needed.
How to fix work lights not functioning properly on Gehl Front End Loaders?
If the work lights on your Gehl Front End Loader aren't functioning properly, it could be due to several reasons: If a single light doesn’t work, the light bulb might be burned out or there could be faulty wiring. If no lights work at all, a 20 ampere breaker might be tripped, or there could be a faulty light switch or poor ground. Check and replace the light bulb as needed. Check the wiring connection to the light. Check the circuit and locate the trouble before replacing the fuse. Replace the light switch. Check the ground wire connections.
Why are no instrument panel lamps on when the keyswitch is turned to “ON” on my Gehl Front End Loader?
If no instrument panel lamps illuminate when the keyswitch is turned to “ON” in your Gehl Front End Loader, it could be due to a tripped 20 ampere breaker or loose/corroded battery terminals or cables. Check the circuit and locate the trouble before resetting the breaker. Clean the battery terminals and cables and retighten them.
Why does my Gehl Front End Loader engine overheat?
Your Gehl Front End Loader engine may overheat due to several reasons: the crankcase oil level could be too low or too high, the fan air circulation might be blocked or restricted, the fan shroud might be improperly positioned, the grade of oil might be improper or excessively dirty, the exhaust could be restricted, the air filter could be restricted, the coolant level could be low, or the fan belt could be loose. To address this, add or remove oil as required. With the engine OFF, remove any blockage or restriction to the fan. Drain and replace the oil with the proper grade of new oil. Allow the exhaust to cool, then remove any restriction. Replace the air filter(s). Add coolant. Tighten the fan belt.
What to do if auxiliary hydraulics do not function on Gehl Front End Loaders?
If the auxiliary hydraulics on your Gehl Front End Loader do not function, it could be because the restraint bar is raised, the spool lock solenoid is malfunctioning, the restraint bar or seat switch is malfunctioning, the load sense signal line is loose or broken, the load sense compensator is not functioning, or the high pressure compensator on the pump is not functioning. Lower the restraint bar. Check the electrical connections to the lock solenoid and repair connections as needed. Check the load sense signal line; tighten or replace if necessary.
General| Brand | Gehl |
|---|---|
| Model | SL7600 |
| Category | Front End Loaders |
| Language | English |
To Next Page
