General Monitors 610A - Engineering Documentation; Panel Assembly, Panel Mount - 98, Ref: 10199 C; Figure 10: Panel Assembly, Panel Mount -98, Ref: 10199 C

50 pages

Save Page as PDF

To Next Page

To Previous Page

Model 610A

7.11 Engineering Documentation

7.11.1 Panel Assembly, Panel Mount – 98, Ref: 10199C

Figure 10: Panel Assembly, Panel Mount –98, Ref: 10199C

Main Page

Table of Contents3
Illustrations5
Introduction7
Protection for Life7
Special Warning7
Customer Support8
Before Installation9
Differences between Models 610A and 6109
General Product Description9
Controller10
Figure 1: Model 610A Controller10
Sensor Assembly11
Installation12
Location of the Controller12
Power Connections12
Table 1: Model 610A Mounting Parts12
Battery Backup13
Figure 2: Schematic Battery Backup System13
Figure 3: Outline Drawing & Rear Terminal Connections (REF: 20659)14
Figure 4: Rear Terminal Common Relay Configuration15
Figure 5: Rear Terminal Discrete Relay Configuration16
Analog Output Connection17
Remote Reset Connection17
Choosing Sensor Locations17
Vapor Density17
Air Currents17
Likely Sources of Gas Emission17
Environmental Factors18
Catalytic Poisons18
Sensor Installation18
Table 2: Terminal Colors19
Table 3: Maximum Cable Run Distance19
Figure 6: Junction Box Assembly - Sensor20
Alarm Wiring Connections21
Table 4: Sensor Guards21
Table 5: De-Energized Alarm Relay Contacts21
Table 6: Energized Alarm Relay Terminations21
Special Voting Option22
Figure 7: Protection Circuit for Relay Contacts22
Start-Up and Operation24
Types of User Interfaces24
Figure 8: Front Panel Display24
Initial Application of Power25
Resetting Latched Alarms25
Analog Output25
Calibration Check Mode26
Figure 9: Portable Purge Calibrator26
Calibration Mode27
Aborting Calibration27
Setup and Setup Check Modes28
Entering the Password29
High Alarm Options29
Low Alarm Options29
Calibration Level Option30
Password Enabled/Disabled Option30
LED Test30
Setup Mode Selection Table31
Table 7: Setup Display Options31
Check Points for Calibration and Operation32
Frequency of Calibration32
Background of Combustible Gases32
Replacing a Sensor32
Special Options32
Optional Model 610A Controller for Zone Control (Voting)32
Set up Options33
Table 8: Relay Alarm Options33
Maintenance34
General Maintenance34
Periodic System Verification34
Troubleshooting35
General35
Troubleshooting Table35
Fault Codes36
Table 9: Troubleshooting Table36
Customer Support37
General Monitors' Offices37
Other Sources of Help37
Appendix38
Warranty38
Sensor Operating Principle38
General Specifications - Controller40
Mechanical Specifications40
Environmental Specifications40
Electrical Specifications40
System Specifications40
General Specifications - Sensor40
Cable Requirements41
Sensors41
Table 10: Maximum Cable Lengths41
Table 11: GMI Sensors Available for 610A System41
Accessories42
Calibration Equipment42
Sensor Covers42
Recommended Spare Parts43
Table 12: Recommended Spare Parts43
Sample Calibration Schedule and Checklist44
Product Configuration Tables45
Table 13: Product Configuration Tables46
Engineering Documentation47
Panel Assembly, Panel Mount - 98, Ref: 10199C47
Figure 10: Panel Assembly, Panel Mount -98, Ref: 10199C47
Interconnection Drawing Zone Control Model 610A Controller48
Figure 11: Interconnection Drawing Zone Control Model 610A Controller48

Related product manuals

General Monitors 4802A

75 pages

General Monitors 2180A

45 pages

General Monitors 610A - Engineering Documentation; Panel Assembly, Panel Mount - 98, Ref: 10199 C; Figure 10: Panel Assembly, Panel Mount -98, Ref: 10199 C

Table of Contents

Related product manuals