BLIZZARD 500-900 3 532102 - Rev.B
Translation of the original instructions
ENGLISH
EU DECLARATION OF CONFORMITY
The Manufacturer
Company name: FAAC S.p.A. Soc. Unipersonale
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
hereby declares under his sole responsibility that the following product:
Description: Gear motor for sliding gates
Model: BLIZZARD 500; BLIZZARD 900.
Complies with the following relevant Union harmonization legislations:
2014/30/EU
2011/65/EU
Furthermore, the following harmonised standards have been applied:
EN61000-6-2:2005
EN61000-6-3:2007 + A1:2011
Bologna, Italy, 06-12-2018 CEO
A. Marcellan
CONTENTS
1. INTRODUCTION TO THIS INSTRUCTION MANUAL .......... 4
1.1 Meaning of Symbols Used ....................................... 4
2. SAFETY RECOMMENDATIONS .................................. 5
2.1 Installer safety .................................................... 5
2.2 Transport and storage ............................................ 5
2.3 Unpacking and handling ........................................ 6
2.4 Disposal of the product .......................................... 6
3. BLIZZARD 500-900 ................................................ 6
3.1 Intended use ...................................................... 6
3.2 Limitations of use ................................................. 6
3.3 Prohibited uses ................................................... 6
3.4 Emergency Use ................................................... 7
3.5 Product Warnings ................................................. 7
3.6 Product Identification ............................................ 7
3.7 Technical Characteristics ......................................... 7
3.8 Component Identification ....................................... 8
3.9 Dimensions ........................................................ 8
4. INSTALLATION REQUIREMENTS ................................ 9
4.1 Mechanical Requirements ....................................... 9
4.2 Electrical System .................................................. 9
4.3 Example System .................................................10
5. INSTALLATION ................................................... 10
5.1 Tools Required ...................................................10
5.2 Installation Dimensions .........................................11
5.3 Base plate .........................................................12
5.4 Fastening the Gear Motor.......................................12
5.5 Manual Operation ...............................................13
5.6 Installing the Rack ...............................................13
5.7 Adjustments and Checks .......................................16
6. START-UP.......................................................... 17
6.1 Power supply and grounding ..................................17
6.2 Installation of the Limit Switches ..............................17
6.3 Final Operations .................................................18
7. MAINTENANCE
................................................... 18
7.1 Scheduled Maintenance ........................................19
8. INSTRUCTIONS FOR USE ....................................... 20
8.1 Safety recommendations .......................................20
8.2 Product Warnings ................................................ 20
8.3 Emergency Use ..................................................20
8.4 Manual Operation ...............................................20
DECLARATION OF INCORPORATION FOR PARTLY
COMPLETED MACHINERY
(2006/42/EC ANNEX II P.1, B)
Manufacturer and person authorised to draft the applicable technical documentation
Company name: FAAC S.p.A. Soc. Unipersonale
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
Hereby declares that the partly completed machinery:
Description: Gear motor for sliding gates
Model: BLIZZARD 500; BLIZZARD 900.
the following essential requirements of the Machinery Directive 2006/42/EC
(including all applicable amendments) have been applied and fulfilled:
1.1.2, 1.1.3, 1.1.5, 1.1.6, 1.2.3, 1.2.6, 1.3.1, 1.3.2,
1.3.4, 1.3.9, 1.4.1, 1.4.2.1, 1.5.1, 1.5.2, 1.5.5, 1.5.6,
1.5.7, 1.5.8, 1.5.10, 1.6.1, 1.6.4, 1.7.1, 1.7.2, 1.7.3,
1.7.4.2, 1.7.4.3
and that the relevant technical documentation has been compiled in compliance
with part B of Annex VII.
Furthermore, the following harmonised standards have been applied:
EN60335-1:2012 + A11:2014
EN60335-2-103:2015
EN 12100:2010
EN 13849-1:2015 CAT 2 PL “C”
EN 13849-2:2012
Undertakes to transmit by mail or by e-mail, in response to a reasoned request by
the national authorities, relevant information on the partly completed machinery.
It is also declared that the partly completed machinery identified above may not be com-
missioned until the final machine - into which it will be incorporated - has been declared
complaint with the provisions of the above mentioned Machine Directive 2006/42/EC.
Bologna, Italy, 06-12-2018 CEO
A. Marcellan
To Next Page
Loading...
