Need help?Do you have a question about the Gilbarco FlexPay IV CRIND and is the answer not in the manual?
Provides start-up instructions for the FlexPay IV CRIND outdoor terminal platform.
Identifies the target audience as Gilbarco-trained and certified Authorized Service Contractors (ASCs).
Covers hazards and safety precautions for installing, inspecting, maintaining, or servicing the product.
Details emergency shut-off, evacuation, barricading, and shutting off protocols.
Explains warning symbols and signal words (DANGER, WARNING, CAUTION) used in the manual.
Discusses hazards of electricity, open flames, sparks, and static electricity with fuels.
Warns about hazardous materials and recommends working with a partner.
Provides instructions for responding to emergencies involving ingested or inhaled substances.
Explains Lockout/Tagout procedures for machine servicing and maintenance.
Lists requirements before proceeding with FlexPay IV startup, including OS, POS version, and IP scheme.
Details the steps for powering on and initiating the FlexPay IV startup process.
Explains how to enter the password on the Maintenance Menu screen to proceed.
Guides on configuring the CRIND device on Side A, including device selection and port settings.
Describes how to set the time zone for the unit using the keypad.
Details configuring secure menu settings, including time, IP addresses, and system activation.
Explains how to set the local time and date, or use the NTP server for synchronization.
Covers the unit activation process and troubleshooting error messages for enabled modules.
Describes jumper settings for the Dispenser Communication Module (DCM)2.1/DCM2.2.
Details how to configure CRIND IP addresses for units equipped with SSoM.
Guides on configuring CRIND IP addresses for units that do not have SSoM.
Instructions for configuring the CRIND for Side B, referencing Side A procedures.
Details how to configure the Applause Media System for startup and operation.
Final steps to complete the startup process, including reconnecting cables and verifying functionality.
Lists related documents for further information on the FlexPay IV system.
Provides a glossary of terms and acronyms used throughout the manual.
Describes various system screens encountered during operation and setup.
Details the Service Menu startup screen and password generation from the Serial Number.
Explains the "System Offline" and "Out of Service" screens indicating system status.
Covers "Tamper Detected" state and the "Software Update" screen.
Outlines accessing the Maintenance Menu and System Menu options.
Describes how to retrieve system information via USB or printer.
Explains device configuration and the IP scheme for units, including UPM, UX-300, and GSOM.
Details the options available within the Device Selection menu for configuring system components.
Guides on setting up the VFI device IP address for new installations or replacements.
Details setting up GSOM A/B IP addresses for new installations or device replacements.
Describes error messages related to IP conflicts or communication troubles.
Covers timezone selection and the process for updating printer firmware.
Explains how to set the time for the daily system restart.
Describes how to perform internal application configuration for the system.
Shows various CRIND BIOS configuration screens for different software versions.
Details the software update process using a USB stick and folder structure.
Explains how to use the Selfcheck Tool to verify system components and diagnostics.
Shows the diagnostic mode screens for software versions 42.06.XX.
Describes how to configure the Cloud application for remote initialization.
Covers accessing Secure Menu, login, and performing maintenance operations.
Explains how to configure and set the unit's date and time for log analysis.
Guides on configuring system network settings, including IP addresses for VFI and GSOM devices.
Describes the Auto Configuration procedure for UPM network setup based on existing devices.
Explains how to activate dismounting sensors and enable system activation for the unit.
Details managing protocols and deleting application packages in the respective menus.
Describes the process to permanently activate SRED functionality on the system.
General| Category | Payment Terminal |
|---|---|
| Manufacturer | Gilbarco |
| Display | Yes |
| Display Type | LCD |
| Type | CRIND |
| Payment Options | Credit, Debit, Contactless, Mobile Payments |
| Connectivity | Ethernet |
| Security | EMV Level 1 & 2 |
| Printer | Optional |
| Dimensions | Varies by model |
| Weight | Varies by model |
To Next Page