How to stop my Gorenje Washer from moving during operation?
If your Gorenje Washer moves during operation, it's likely not properly leveled or the transport brackets haven't been removed. Level the machine using the adjustable legs and ensure all transport brackets are removed.
What to do if my Gorenje Washer won't start and the LEDs are flashing?
If your Gorenje Washer isn't starting and the LEDs are flashing, it's likely because the door isn't closed properly. Push the door firmly towards the machine to ensure it's securely closed.
Why is there excessive foaming during washing in my Gorenje washing machine Washer?
Excessive foaming during washing with your Gorenje Washer is usually due to using too much detergent. Make sure to use washing powder according to the manufacturer's instructions, considering the water hardness and how soiled the laundry is. Also, only use detergents specifically designed for machine washing.
Why does my Gorenje Washer vibrate so much during the spin cycle?
If your Gorenje Washer vibrates excessively during the spin cycle, it's often because the laundry is unevenly distributed, especially when washing very small loads. This is normal; the machine will reduce the spin speed if vibrations are too strong. Try washing a larger quantity of laundry to balance the load.
What to do if water is leaking from my Gorenje Washer?
If water is leaking from your Gorenje Washer, it could be due to a few reasons. The filter might not be tightly screwed in, the inlet pipe may not be tightly connected to the machine or the water faucet, or the outlet pipe may have fallen to the floor. Ensure that the filter and inlet pipe are tightened properly, and affix the outlet pipe securely to the drain.
What to do if my Gorenje Washer is not pumping out water and the LEDs flash seven times?
If your Gorenje Washer is not pumping out water properly (and the LEDs flash seven times), the water outlet may be clogged. Check if the filter is clean, the outlet pipe is not jammed, the drain is not clogged, and the outlet pipe is positioned no higher than 1 meter. Then, push the START button again.
Why is water not entering my Gorenje washing machine Washer and the LEDs flash three times?
If water isn't entering your Gorenje Washer (and the LEDs flash three times), it indicates a disturbed water inlet. Check if the water tap is open and if the inlet pipe net filter is clean. Then, push the START button.
Why are there white powdery residues on my laundry after washing in my Gorenje Washer?
If you find white powdery residues on your laundry after washing in your Gorenje Washer, it's likely due to neo-phosphate detergents containing non-soluble components (zeolites) for water softening. These substances can deposit on the laundry. Immediately rinse the laundry again, use liquid detergents without zeolites, or try removing the residues with a brush.
Why is my laundry not properly spun in my Gorenje washing machine Washer, but no failure is reported?
If your laundry isn't properly spun in your Gorenje Washer, but no failure is reported, the machine may have activated the UKS function. This means the machine has automatically reduced the spin speed due to bad laundry balance. The machine is operating normally. Try washing large and small pieces of laundry together to balance the load.
Why are there detergent residues in the dispenser of my Gorenje washing machine?
If you see detergent residues in the dispenser of your Gorenje Washer, it could be due to low water flow pressure or some detergents sticking to a wet dispenser. Clean the inlet pipe filter net, increase the water level if there's low water pressure, and wipe the dispenser before loading detergent.
Critical safety instructions and warnings to prevent damage, injury, and ensure correct operation of the washing machine.
Details unpacking the appliance and removing transport brackets to prevent damage during operation.
Instructions for connecting the water supply hose, including water pressure and Aqua-stop system details.
Instructions for connecting the drain hose and plugging the appliance into the mains power supply safely.
Overview of the control panel, buttons, display, and program selector for choosing wash cycles.
Step-by-step guide for loading laundry, selecting programs, adding agents, and initiating the wash cycle.
Explains machine fault signaling, lists common error codes, and provides initial steps for self-correction.
Comprehensive table detailing common failures, their possible causes, and recommended solutions.
Critical safety instructions and warnings to prevent damage, injury, and ensure correct operation of the washing machine.
Details unpacking the appliance and removing transport brackets to prevent damage during operation.
Instructions for connecting the water supply hose, including water pressure and Aqua-stop system details.
Instructions for connecting the drain hose and plugging the appliance into the mains power supply safely.
Overview of the control panel, buttons, display, and program selector for choosing wash cycles.
Step-by-step guide for loading laundry, selecting programs, adding agents, and initiating the wash cycle.
Explains machine fault signaling, lists common error codes, and provides initial steps for self-correction.
Comprehensive table detailing common failures, their possible causes, and recommended solutions.
This document provides instructions for use of a washing machine, designed for modern laundry treatment with rational consumption of energy, water, and washing agents. The appliance is intended exclusively for household use.
The washing machine offers a variety of programs and additional functions to cater to different laundry needs. Basic programs include:
Partial programs include:
Additional functions modify the basic washing cycle:
(Depending on model)
To Next Page
General