What to do if my Gravely Lawn Mower engine cranks but does not start?
If your Gravely Lawn Mower engine cranks but doesn't start, consider these possibilities: * The fuel tank might be empty. Refill the fuel tank. * The battery might be weak. Check the voltage and charge if required.
Why does my Gravely Pro-Stance 52 EFI Lawn Mower engine crank but not start?
If your Gravely Lawn Mower's engine cranks but doesn't start, several factors could be at play. First, ensure the fuel tank isn't empty and fill it if needed. A weak battery can also prevent starting, so check the voltage and charge if required.
Why won't my Gravely Pro-Stance 52 EFI Lawn Mower engine crank?
If your Gravely Lawn Mower engine won't crank, here are several potential causes and solutions: * The PTO might be engaged. Disengage the PTO. * The parking brake might be disengaged. Engage the parking brake. * Battery cables could be loose or corroded. Clean and tighten the battery cables. * The battery might be discharged or weak. Charge the battery and check the voltage. * There may be a blown fuse. Check the main fuse and replace it if necessary. * A relay in the fuse block may have failed. Check the relays and replace if needed. * There might be loose or broken wires. Inspect the wire harness and connections.
Why is my Gravely Lawn Mower not driving?
If your Gravely Lawn Mower isn't driving, here are a few things to check: 1. Ensure the parking brake is disengaged. 2. Confirm that the transmission bypass levers are closed. 3. Check the hydraulic oil level and add oil if it's low.
Why won't the PTO or mower blades engage or shut off on my Gravely Lawn Mower?
If the PTO or mower blades on your Gravely Lawn Mower won't engage or shut off, it might be because the operator presence switch is not depressed. Depress the operator presence switch by holding down the right steering control handle.
What to do if my Gravely Pro-Stance 52 EFI Lawn Mower cranks but does not start?
If your Gravely Lawn Mower engine cranks but doesn't start, several factors could be responsible. Start by ensuring the fuel tank isn't empty and that the fuel supply is adequate. A weak battery can also prevent starting, so check the voltage and charge if required.
Why does my Gravely Pro-Stance 52 EFI Lawn Mower unit not drive?
If the unit does not drive, first disengage the parking brake. Also, ensure that the transmission bypass levers are closed. Check the hydraulic oil level and add oil if it is low.
Why won't the PTO or mower blades engage on my Gravely Pro-Stance 52 EFI?
If the PTO or mower blades on your Gravely Lawn Mower do not engage or shut off, make sure the operator presence switch is depressed by holding down the right steering control handle.
What to do if my Gravely Pro-Stance 52 EFI engine continues to run when ignition key is off?
If your Gravely Lawn Mower engine continues to run when the ignition key is in the off position, it could be due to: * A disconnected ignition ground wire. Connect the ground wire to a clean metal surface.
Why does my Gravely Lawn Mower engine not crank?
If your Gravely Lawn Mower engine won't crank, there are several potential causes. First, ensure the PTO is disengaged and the parking brake is engaged. Check for loose or corroded battery cables, and clean and tighten them if necessary. A discharged or weak battery could also be the culprit, so charge the battery or check its voltage. Additionally, inspect the main fuse and relays in the fuse block, replacing them if needed. Finally, examine the wire harness and connections for any loose or broken wires.
Explanation of safety alert symbols and signal words used in the manual.
How to use the steering levers for control and direction.
Testing the safety interlock system for proper function.
Understanding the parking brake's interaction with steering levers.
Steps to start engines equipped with a carburetor.
Steps to start engines with electronic fuel injection.
Procedures for stopping the unit safely in emergency situations.
Checking and changing the engine oil.
General| Cutting Width | 52 inches |
|---|---|
| Transmission | Hydro-Gear ZT-3400 |
| Blade Tip Speed | 18, 500 fpm |
| Turning Radius | Zero-turn |
| Cutting Height | 1.5 - 5 inches |
| Spindle Material | Aluminum |
| Warranty | 2-year limited warranty |
To Next Page
