To Next PageTo Next PageWhat to do if Gree Heat Pump does not heat although compressor is running?
If your Gree Heat Pump isn't heating despite the compressor running, a possible cause is refrigerant leakage, which requires leakage detection and refrigerant replenishment. Another potential cause is a malfunctioning compressor, which would need replacement.
How to improve hot water heating efficiency of Gree Heat Pump?
If your Gree Heat Pump has poor hot water heating efficiency, check for poor heat insulation in the water system and enhance it. Also, check for poor heat exchange of the evaporator by ensuring normal air flow and cleaning the evaporator. Poor refrigerant levels due to leaks can also cause this, so check for refrigerant leaks. Finally, a blockage in the heat exchanger on the water side can reduce efficiency; clean or replace the heat exchanger if needed.
What causes heavy noise of Gree GRS-CQ16Pd/NhG-K Heat Pump compressor?
Heavy noise from the Gree Heat Pump compressor can occur if liquid refrigerant enters the compressor, leading to liquid slugging. Check the expansion valve and temperature sensor for failures or looseness, and repair if necessary. Alternatively, internal parts in the compressor may be broken, requiring compressor replacement.
What to do if Gree GRS-CQ16Pd/NhG-K Heat Pump fan makes a heavy noise?
If the Gree Heat Pump fan is making excessive noise, it could be due to a loose fixing bolt, which needs to be re-fixed. Alternatively, the fan blade might be touching the shell or grill, requiring adjustments. Unreliable fan operation may also cause noise, indicating the fan needs replacement.
What to do if Gree Heat Pump water pump does not run?
If the Gree Heat Pump water pump isn't running or is running abnormally, it could be due to a malfunction in the power supply or terminal, requiring you to find out the reasons and repair it. A malfunctioning relay could also be the cause, necessitating a relay replacement. Another potential issue is air in the water pipe, which needs to be evacuated.
Why won't my Gree GRS-CQ16Pd/NhG-K compressor start?
If the Gree Heat Pump compressor isn't starting, it could be due to a power supply issue such as a reversed phase sequence. It may also be due to loose connection wires, which should be checked and re-fixed. A malfunction of the mainboard or the compressor itself could also be the cause, requiring repair or replacement, respectively.
Why does my Gree GRS-CQ16Pd/NhG-K compressor start and stop frequently?
If your Gree Heat Pump compressor frequently starts and stops, it could be due to poor or excess refrigerant; in this case you should discharge or add part of the refrigerant. It might also be caused by poor circulation in the water system, potentially due to blockages or air, so inspect the water pump, valve, and pipeline, cleaning the water filter or evacuating air as needed. A low load can also cause this issue; try adjusting the load or adding accumulating devices.
General| Heating Seasonal Performance Factor (HSPF) | 4.0 |
|---|---|
| Refrigerant | R410A |
| Voltage | 220-240 V |
| Energy Efficiency Ratio (Cooling) | 3.21 |
| Frequency | 50 Hz |
Important introductory information and responsibilities for users of the heat pump.
Essential safety instructions, warnings, and notes for safe operation and installation.
Safety procedures and precautions related to flammable refrigerants like R32.
Explanation of the unit's functions in cooling, heating, and water heating modes.
Identification of model codes, parameters, main components, and unit specifications.
Illustrative cases for connecting under-floor coils, water tanks, and FCUs.
Instructions for unit location, dimensions, precautions, and pipe connections.
Details on hydraulic connections, water tank setup, and water quality.
Recommended power cable specifications and leakage switch types.
Control board wiring, electrical specifications, and terminal board connections.
Procedures for pre-startup checks, test runs, and unit acceptance.
Guidance on routine operation, maintenance, and troubleshooting.
Procedures for refrigerant recovery, decommissioning, and service.
