Gree GVH36ALXH-K3NTC7A/I - Page 27

24
Technical Information
Service Manual
When selecting auto mode, air conditioner will operate
automatically according to the sensed temperature. Set
temperature can’t be adjusted and will not be displayed as well.
Press "FAN" button can adjust fan speed. Press " " / " "
button can adjust fan blowing angle.
● After selecting cool mode, air conditioner will operate under
cool mode. Cool indicator " " on indoor unit is ON (This
indicator is not available for some models). Press "▲" or "▼"
button to adjust set temperature. Press "FAN" button to adjust
fan speed. Press " " / " " button to adjust fan blowing angle.
● When selecting dry mode, the air conditioner operates at low
speed under dry mode. Dry indicator " " on indoor unit is
ON(This indicator is not available for some models). Under dry
mode, fan speed can’t be adjusted. Press " " / " " button to
adjust fan blowing angle.
● When selecting fan mode, the air conditioner will only blow fan,
no cooling and no heating. Fan indicator " " on indoor unit is
ON. Press "FAN" button to adjust fan speed. Press " " / " "
button to adjust fan blowing angle.
● When selecting heating mode, the air conditioner operates
under heat mode. Heat indicator " " on indoor unit is ON(This
indicator is not available for some models). Press "▲" or "▼"
button to adjust set temperature. Press "FAN" button to adjust
fan speed. Press " " / " " button to adjust fan blowing angle.
(Cooling only unit won’t receive heating mode signal. If setting
heat mode with remote controller, press ON/OFF button can’t
start up the unit).
NOTE:
● For preventing cold air, after starting up heating mode, indoor
unit will delay 1~5 minutes to blow air (actual delay time is
depend on indoor ambient temperature).
● Set temperature range from remote controller: 16~30°C
(61~86°F); Fan speed: auto, quiet speed, low speed, medium
speed, high speed, turbo speed.
3. FAN button
Pressing this button can set fan speed circularly as: auto (AUTO),
QUIET( ), low( ), medium( ), high( ), turbo( ).
● Under AUTO speed, air conditioner will select proper fan
speed automatically according to ex-factory setting.
● It’s Low fan speed under Dry mode.
● Turbo cannot be set in FAN mode.
4. SAVE button
Under cooling mode, press this button to start up or turn off
energy-saving function. When energy-saving function is started
up, "SE" will be shown on remote controller, and air conditioner
will adjust the set temperature automatically according to ex-
factory setting to reach to the best energy-saving effect. Press
this button again to exit energy-saving function.
5.
▲ / ▼
button
● Press "▲" or "▼" button once increase or decrease set
temperature 1°C (°F). Holding "▲" or "▼" button, 2s later,
set temperature on remote controller will change quickly. On
releasing button after setting is finished, temperature indicator
on indoor unit will change accordingly. (Temperature can’t be
adjusted under auto mode)
● When setting TIMER ON, TIMER OFF, press "▲" or "▼" button
to adjust time. (Refer to TIMER button for details)
6. COOL button
● Press this button, unit will operate in cool mode.
7. HEAT button
● Press this button, unit will operate in heat mode.
8. button
● Under simple swing mode, press this button can turn on ("
" icon is displayed) or turn off (" " icon is not displayed) the
left & right swing function.
● When the unit is turned off by remote controller, press "▲"
button and " " button can switch between single swing mode
and xed-angle swing mode. " " on the remote controller will
ash twice. Under xed-angle swing mode, press this button and
then left&right swing status will circulate as shown in the right
gure:
no display
● This remote controller is the general type remote controller.
When remote controller receives the signal of " " , swing
status is same as " " ; when remote controller receives " ",
swing status is same as left & right swing OFF.
9. button
● Under simple swing mode, press this button can turn on ( "
" icon is displayed) or turn off (" " icon is not displayed) the
up & down swing function.
● When the unit is turned off by remote controller, press "▲"
button and " " button can switch between single swing mode
and xed-angle swing mode. " " on the remote controller will
ash twice. Under xed-angle swing mode, press this button and
the up & down swing status will circulate as shown in the right
gure:
no display