20
Technical Information
Service Manual
12. QUIET button(This function is unavailable for this model)
13. X-FAN button
14. LIGHT button
16. TEMP button
15. button(This function is unavailable for this model)
Press this button, the Quiet status is under the Auto Quiet mode (display " " and "AUTO" signal ) and Quiet mode (display " " singal)
and Quiet OFF (there is no signal of " " displayed), after powered on, the Quiet OFF is defaulted.
Note:
●
The Quiet function cannot be set up in Fan and Dry mode; Under the Quiet mode,
the fan speed is not available.
● If Auto Quiet mode has been selected, after the room temperature reached the setting temperature or 10mins later, the AC will immediately
enter into the Quiet running status, at this time the fan speed is not adjustable.
Pressing this button in COOL or DRY mode, the icon " " is displayed and the indoor fan will continue operation for 2 minutes in order to
dry the indoor unit even though you have turned off the unit. After energization, X-FAN OFF is defaulted.
X-FAN is not available in AUTO, FAN or HEAT mode.This function indicates that moisture on evaporator of indoor unit will be blowed after
the unit is stopped to avoid mould.
● Having set X-FAN function on: After turning off the unit by pressing ON/OFF button indoor fan will continue running for about 2 minutes. at
low speed. In this period, press X-FAN button to stop indoor fan directly.
● Having set X-FAN function off: After turning off the unit by pressing ON/OFF button, the complete unit will be off directly.
Press this button to turn off display light on indoor unit. " " icon on remote controller disappears. Press this button again to turn on
display light. " " icon is displayed.
By pressing this button, you can see indoor set temperature, indoor ambient temperature or outdoor ambient temperature on indoor unit’s
display. The setting on remote controlleris selected circularly as below:
Press this button to achieve the on and off of healthy and scavenging functions in operation status. Press this button for the rst time to start
scavenging function; LCD displays " ". Press the button for the second time to start healthy and scavenging functions simultaneously;
LCD displays " " and " " . Press this button for the third time to quit healthy and scavenging functions simultaneously. Press the button
for the fourth t ime to start healthy function; LCD display " " . Press this button again to repeat the operation above.
no display
11. CLOCK button
Press this button to set clock time. " " icon on remote controller will blink. Press " ▲ " or "
▲
" button within 5s to set clock time. Each
pressing of " ▲ " or "
▲
" button, clock time will increase or decrease 1 minute. If hold " ▲ " or "
▲
" button, 2s later, time will change quickly.
Release this button when reaching your required time. Press "CLOCK" button to conrm the time. " " icon stops blinking.
Note:
● Clock time adopts 24-hour mode.
● The interval between two operation can’t exceeds 5s. Otherwise, remote controller will quit setting status. Operation for TIMER ON/TIMER
OFF is the same.
● TIMER OFF button
"TIMER OFF" button can set the time for timer off. After pressing this button," "icon disappears and the word "OFF" on remote controller
blinks. Press " ▲ " or "
▲
" button to adjust TIMER OFF setting. After each pressing " ▲ " or "
▲
" button, TIMER OFF setting will increase
or decrease 1min. Hold " ▲ " or "
▲
" button, 2s later, the time will change quickly until reaching your required time. Press "TIMER OFF"
word "OFF" will stop blinking. " " icon resumes displaying. Cancel TIMER OFF. Under the condition that TIMER OFF is started up, press
"TIMER OFF" button to cancel it.
Note:
● Under on and off status, you can set TIMER OFF or TIMER ON simultaneously.
● Before setting TIMER ON or TIMER OFF, please adjust the clock time.
● After starting up TIMER ON or TIMER OFF, set the constant circulating valid. After that, air conditioner will be turned on or turned off
according to setting time. ON/OFF button has no effect on setting. If you don’t need this function, please use remote controller to cancel it.
To Next Page
Loading...
