Gree PULAR Series

34
Technical Information
Service Manual
When WiFi function is turned on, " WiFi " icon will be displayed
on the remote controller; when WiFi function is turned of
f,
" WiFi " icon will disappea
r.
Ho
w to turn on WiFi: Press " WiFi " button to turn on WiFi
●
This function is only available for some models.
function.
How to turn of
f WiFi: Hold " WiFi " button for 5s to turn off WiFi
function.
Under
off status, press "MODE" and " WiFi " buttons
simultaneously
for 1s, WiFi module will restore factory
settings.
●
Press
this button to turn off display light on indoor unit. " "
icon on remote controller disappears.
Press
this button again to turn on display light. " " icon is
displayed.
Pres
s this button to achieve the on and off of health and
scavenging functions in operation station. Press this button for
"
". Press the button for the second time to start health and
scavenging functions simultaneously; LCD displays
"
" and " ". Press this button for the third time to quit
healt
h and scavenging functions simultaneously. Press the
button
for the fourth time to start health function; LCD display
"
". Press this button again to repeat the operation above.
Energy-saving function
Under
cooling mode, press "TEMP" and "CLOCK" buttons
simultaneously
to start up or turn off energy-saving function.
When energy-saving function is started up, "SE" will be shown
on
remote controller, and air conditioner will adjust the set
temperature
automatically according to ex-factory setting to
reach to the best energy-saving ef
fect.
Press
"TEMP" and "CLOCK" buttons simultaneously again to
exit energy-saving function.
●
speed and it can't be adjusted.
●
Under 8
đ
heating function, fan speed is defaulted at auto
Under 8
đ
heating function, set temperature can't be
●
adjusted. Press "TURBO" button and the remote controller
won't send signal.
Sleep function and 8
đ
heating function can't operate at the
8
℃
heating function(This function is not available for cool
only models.)
Under heat mode, press "TEMP" and "CLOCK" buttons
simultaneously to start up or turn off 8
đ
heating function
.
When this function is started up, " " and "8
đ
" will be
shown on remote controller, and the air conditioner keep
the
heating status at 8
đ
. Press "TEMP" and "CLOCK" buttons
simultaneously again to exit 8
đ
heating function.
Notice:
●
display 46
ē
heating.
Child lock function
Under
ē
temperature display, the remote controller will
same time. If 8
đ
heating function has been set under h
eat
mode, press sleep button will cancel 8
đ
heating function. I
f
sleep function has been set under heat mode, start up the 8
đ
heating function will cancel sleep function.
Auto clean function
Temperature display switchover function
Under OFF status, press "▼" and "MODE" bu ttons
simultaneously to switch temperature display between
đ
and
ē
.
Press "▲" and "▼" simultaneously to turn on or turn of
f
child lock function. When child lock function is on, " " i
con
is displayed on remote controller. If you operate the r
emote
controller, the " " icon will blink three times without
sending
signal to the unit.
WiFi
Notice:
●
Press
this button, you can see indoor set temperature, indoor
ambient
temperature on indoor unit' s display. The setting on
remote controller is selected circularly as below:
auto speed and it can't be adjusted.
●
Under energy-saving function, fan speed is defaulted at
Under energy-saving function, set temperature can't be
●
adjusted. Press "TURBO" button and the remote controller
won't send signal.
Sleep function and energy-saving function can't operate at
Under unit off status, hold "MODE" and "FAN" buttons
simultaneously for 5s to turn on or turn off the internal
clean
function. When the internal clean function is turned on,
indoor unit displays “CL” . During the self-cleaning process of
evaporator, the unit will perform fast cooling or fast heating.
or thermal expansion or cold shrinkage. The air conditioner
may blow cool or warm air, which is a normal phenomenon.
This function is applicable to partial of models .
LIGHT
TEMP
the same time. If energy-saving function has been set
under
cool mode, press sleep button will cancel energy-savin
g
function. If sleep function has been set under cool mode, start
up the energy-saving function will cancel sleep function.
no display
Function
introduction for combination
buttons