EasyManua.ls Logo

GreenTec RI 60 - User Manual

Default Icon
66 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
BARRIER MOWER RI 60
– 80
FOX REDSKABSRAMME 2302 – 2802 – 3302
1. UDGAVE 2021
3. EDITION

Table of Contents

Questions and Answers

  • O
    operezAug 13, 2025
    Why is my GreenTec Construction Equipment overheating?
    • L
      Lauren NguyenAug 13, 2025
      Your GreenTec Construction Equipment may be overheating due to several reasons: the oil flow might be too high (check and reduce it to the specified max flow), the radiator could be clogged (clean it by removing leaves, dirt, and debris), the hydraulic system might be overloaded (consider using a vehicle with greater capacity or reducing the attachment tool performance/forward speed), or the oil type might be incorrect (check and change the oil type).
  • P
    perezterriAug 16, 2025
    What to do if the hydraulic system fails in GreenTec Construction Equipment?
    • H
      Holly FrederickAug 16, 2025
      If the hydraulic system fails in your GreenTec Construction Equipment, there are several potential causes to investigate: the oil level might be too low (fill the vehicle with oil to the correct level), a pressure hose could be pinched or bent (check all hydraulic hoses for pinching and damage), there might be an oil leak in the hydraulic system (check for leaks and repair hoses and fittings), or the oil pump suction filter could be stopped (replace the filter insert).
  • M
    Mary GomezAug 20, 2025
    How to fix an uneven mowing result with GreenTec Construction Equipment?
    • G
      ggilmoreAug 20, 2025
      An uneven mowing result with GreenTec Construction Equipment can be caused by broken or worn knife blades or incorrect oil flow. To resolve this, change the knife blades and check the oil flow.
  • K
    kathybatesAug 25, 2025
    How to fix leaking valves or hoses on GreenTec Construction Equipment?
    • D
      Douglas DavisAug 25, 2025
      If you notice valves or hoses leaking on your GreenTec Construction Equipment, it's likely that the hoses or fittings are loose. Tighten the hoses and fittings to resolve this issue.
  • J
    jessica59Aug 28, 2025
    What to do if GreenTec Construction Equipment does not cut?
    • M
      Megan GreenAug 28, 2025
      If your GreenTec Construction Equipment isn't cutting, it could be because the rotating parts are touching the ground or are being held firmly, or the oil flow is incorrect. Adjust the working height and check the oil flow.
  • S
    smithamySep 1, 2025
    Why does the clipping/mowing stop on my GreenTec Construction Equipment?
    • M
      Melissa ParkSep 1, 2025
      If the clipping or mowing stops on your GreenTec Construction Equipment, it may be due to oil overheating. Adjust the working height and reduce forward speed to address this issue.
  • D
    Daniel MillerSep 4, 2025
    Why is my GreenTec Construction Equipment making noise during work?
    • C
      Carmen AndradeSep 5, 2025
      If your GreenTec Construction Equipment is making noise during work, it could be due to insufficient lubrication of the ball bearings in the cutting part. Lubricate according to instructions and remove any foreign bodies.
  • B
    Brandon EllisSep 8, 2025
    What causes abnormally many vibrations in GreenTec Construction Equipment?
    • M
      Matthew VasquezSep 8, 2025
      Abnormally many vibrations in GreenTec Construction Equipment can be caused by broken or worn knife blades. Change the knife blades to resolve this issue.

GreenTec RI 60 Specifications

General IconGeneral
BrandGreenTec
ModelRI 60
CategoryLawn Mower
LanguageEnglish