Why does my GreenWorks G40LM41 Lawn Mower motor stop while cutting?
If your GreenWorks Lawn Mower motor stops while cutting, it might be due to the cutting height being set too low. Try raising the cutting height. Alternatively, the battery may be out of power; in this case, charge the battery.
What to do if my GreenWorks G40LM41 Lawn Mower is not starting?
If your GreenWorks Lawn Mower is not starting, the battery may be low. Charge the battery. Another possibility is that the battery is inoperable or won't take a charge, in which case you should replace it.
How to fix GreenWorks G40LM41 Lawn Mower cutting grass unevenly?
If your GreenWorks Lawn Mower is cutting grass unevenly, the lawn might be rough or uneven, or the cutting height might not be set properly. Move the wheels to a higher position. Ensure all wheels are at the same cutting height for even cutting.
Why is my GreenWorks Lawn Mower not bagging properly?
If your GreenWorks Lawn Mower is not bagging properly, the cutting height may be set too low. Try raising the cutting height.
What to do if GreenWorks Lawn Mower is not mulching properly?
If your GreenWorks Lawn Mower is not mulching properly, wet grass clippings may be sticking to the underside of the deck. Wait until the grass dries before mowing.
Why is my GreenWorks Lawn Mower vibrating at a higher speed?
If your GreenWorks Lawn Mower is vibrating at a higher speed, the blade might be unbalanced or excessively worn. Consider replacing the blade. Also, the motor shaft could be bent. In that case, stop the motor, remove isolator key and battery, disconnect the power source, and inspect for damage. Have it repaired by an authorised service center before restarting.
Why is my GreenWorks Lawn Mower hard to push?
If your GreenWorks Lawn Mower is hard to push, it could be due to high grass, the rear of the mower housing and blade dragging in heavy grass, or the cutting height being too low. Try raising the cutting height.
How to position handle on GreenWorks G40LM41?
If the handle of your GreenWorks Lawn Mower is not in position, it might be because the carriage bolts are not seated properly. Adjust the height of the handle and ensure the carriage bolts are correctly seated.
Carefully remove the product and accessories from the box, verifying all contents.
Steps to raise and securely fasten the lower handle for proper operation.
Guide for attaching the upper handle to the lower handle using bolts and nuts.
Instructions on how to correctly fit the grass catcher to the mower.
How to insert the mulching plug into the rear discharge opening.
Adjusting the mower's cutting height to suit lawn conditions.
Steps for inserting the battery into the mower for operation.
Procedure for safely disconnecting and removing the battery from the mower.
Instructions on how to safely start and shut down the lawn mower.
Advice on proper mowing techniques, lawn care, and maintenance.
Safety precautions and techniques for operating the mower on inclines.
How to safely remove and empty the grass clippings collector.
Routine checks, cleaning, and tightening of parts for overall upkeep.
Details on the lubrication of bearings and components.
Step-by-step guide for safely changing the mower blade.
General| Type | Push lawn mower |
|---|---|
| Motor type | Brushless |
| Cutting width | 410 mm |
| Product color | Black, Green |
| Built-in display | No |
| Number of wheels | 4 wheel(s) |
| Maximum lawn area | 600 m² |
| Mulching function | Yes |
| Sound power level | 90.3 dB |
| Vibration emission | 1.5 m/s² |
| Sound pressure level | 86 dB |
| Recommended lawn area | 300 m² |
| Maximum cutting height | 80 mm |
| Minimum cutting height | 25 mm |
| Grass collecting volume | 50 L |
| Power source | Battery |
| Battery voltage | 40 V |
Weight and Dimensions| Weight | 18000 g |
|---|
To Next Page