Grifco C10A User Manual

3
Safety symbol and signal word review
This commercial door controller has been designed and tested to oer safe service provided it is installed, operated, maintained
and tested in strict accordance with the instrucons and warnings contained in this manual.
WARNING
WARNING
CAUTION
Mechanical
Electrical
When you see this Signal Word on the following pages, it will
alert you to the possibility of damage to your commercial
door and/or the commercial door opener if you do not
comply with the cauonary statements that accompany it.
When you see these Safety Symbols and Signal Words on the
following pages, they will alert you to the possibility of
serious injury or death if you do not comply with the
warnings that accompany them. The hazard may come from
something mechanical or from electric shock.
SAFETY SYMBOL AND SIGNAL WORD REVIEW
WARNING: Important safety instrucons. It is important for the
safety of persons to follow all instrucons. SAVE these instrucons.
THESE ARE IMPORTANT SAFETY INSTRUCTIONS. FOLLOW ALL INSTRUCTIONS AS INCORRECT
INSTALLATION CAN LEAD TO SEVERE INJURY OR DEATH
Keep commercial door balanced. Scking or binding doors must be
repaired. Commercial doors, door springs, pulleys, brackets and
their hardware are under extreme tension and can cause serious
personal injury. Do not aempt to loosen, move or adjust them. Call
for commercial door service.
Disengage all exisng commercial door locks to avoid damage to commercial door.
Install the wall control (or any addional push buons) in a locaon where the
commercial door is visible during operaon . Do not allow children to operate push
buon(s) or remote control(s). Serious personal injury from a closing commercial door
may result from misuse of the opener.
Do not wear rings, watches or loose clothing while installing or
servicing a commercial door opener.
Permanently fasten all supplied labels adjacent to the wall control as a convenient
reference and reminder of safe operang procedures.
To avoid serious personal injury from entanglement, remove all
ropes connected to the commercial door before installing the door
opener.
Acvate opener only when the door is in full view, free of obstrucons and opener is
properly adjusted. No one should enter or leave the building while the door is in
moon.
Installaon and wiring must be in compliance with your local
building and electrical codes. Connect the power supply cord only to
properly earthed mains.
An electrician must disconnect electric power to the commercial door opener before
making repairs or removing covers.
Moisture and water can destroy the electronic components. Make
sure under all circumstances that water moisture or storage
moisture cannot penetrate the electronics. The same applies for
openings and cable entries.
If the supply cord is damaged, it must be replaced by the manufacturer or its service
agent or a similarly qualied person in order to avoid a hazard
A disconnecon device incorporated in the xed wiring must be provided in
accordance with the wiring rules of the country in which it is installed.
Aer the installaon a nal test of the full funcon of the system
and the full funcon of the safety devices must be done.
The actuang member of a biased-o switch is to be located within direct sight of the
door but away from moving parts. Unless it is key operated, it is to be installed at a
minimum height of 1500mm and not accessible to the public.
When operang a biased-o switch, make sure that other persons
are kept away.
Make sure that people who install, maintain or operate the door follow these
instrucons. Keep these instrucons in a safe place so that you can refer to them
quickly when you need to.
The opener cannot be used with a driven part incorporang a
wicket door (unless the opener cannot be operated with the wicket
door open).
If the opener is installed at a height less than 2.5 metres from oor level or any other
level from which the unit can be accessed (eg mezzanine) the installer is responsible
to t guards to the opener to prevent access to the chain drive.
Ensure that entrapment between the driven part and the
surrounding xed parts due to the opening movement of the driven
part is avoided
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilies, or lack of experience and knowledge, unless
they have been given supervision or instrucon concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
Motor may become hot during operaon. Appropriate clearance
and/or shielding should be supplied by the installer to ensure any
cabling, wiring and/or other items cannot come in contact with the
motor. If temperature rise exceeds 50⁰C all xed wiring insulaon
must be protected, for example, by insulang sleeving having an
appropriate temperature rang.
Use the commercial door accessory for its intended purpose.

Grifco C10A Specifications

General

Brand	Grifco
Model	C10A
Category	Controller
Language	English