Groen TDH-CE Mark User Manual

32 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

SPARE PARTS DIAGRAM FOR

First Choice Group

Blakeney Way, Kingswood

Lakeside

Cannock,

Staffs,

WS11

8LD

TEL: 01543

577778

FAX:

01543504141

Email:

enquires@firstchoice-cs.co.uk

Web:

www.firstchoice-cs.co.uk

Steam Jacketed Kettle

TDH-CE Mark

Table of Contents

Questions and Answers:

J
Jenna PalmerAug 22, 2025
Why won't the burners light on my Groen Kettle?
- W
  wareangelaAug 22, 2025
  If the burners on your Groen Kettle won't light, there are several things to check: * Make sure the main gas supply cock is open (the handle should be in line with the gas pipe). * Verify the gas supply to the building. * Ensure the kettle body is not tilted. * Confirm the electric power supply to the unit is on. * Examine the thermostat operation. * Check that the tilt limit switch is closed when the kettle body is not tilted.
J
Jennifer MilesSep 2, 2025
Why does my Groen TDH-CE Mark Kettle stop heating before it reaches the desired temperature?
- J
  Jeffrey SmithSep 2, 2025
  If your Groen Kettle stops heating before it reaches the desired temperature, check the thermostat dial setting, the thermostat calibration, and the thermostat operation.
D
David CurtisAug 31, 2025
Why does my Groen TDH-CE Mark Kettle continue heating after reaching the desired temperature?
- R
  rossrhondaAug 31, 2025
  If your Groen Kettle continues heating after reaching the desired temperature, check the thermostat dial setting, the thermostat calibration, and the thermostat operation.
M
Michelle HarrisAug 30, 2025
What to do if there is a spark, but the pilot will not light on Groen TDH-CE Mark?
- M
  Maxwell ColeAug 30, 2025
  If there's a spark but the pilot won't light on your Groen Kettle, try the following: * Check that the gas valve is opening. * Confirm that the gas pressure meets the control manufacturer’s specifications. * Check for gas at the pilot. If there's no gas flow, inspect the pilot gas line for kinks and obstructions. * If necessary, replace the gas control valve. * Ensure the pilot spark gap is 7/64 inch (2.78 mm) and located in the pilot gas stream; adjust or replace the pilot if needed. * Inspect the orifice and clean it if necessary.
L
Lucas HolmesAug 29, 2025
Why Groen TDH-CE Mark system does not produce a spark?
- A
  anthony60Aug 29, 2025
  If your Groen Kettle system isn't producing a spark, here's what to check: * Examine the thermostat and close the contacts if they are open. * Check the AC voltage between terminals '1' and GND. If it’s not 230 VAC, check the high limit switch to ensure it is closed. * Inspect the pilot spark gap and regap it if it is not 7/64 inch (2.78 mm). * Look for cracks or breaks in the electrode ceramic. * Ensure the high tension cable is firmly attached and in good condition; replace the pilot if the cable is cracked or brittle. * If none of the above steps work, replace the electronic spark ignition module.
T
Timothy PerryAug 27, 2025
What to do if the main burner comes on but will not stay lit on Groen TDH-CE Mark?
- J
  Jason CaseyAug 27, 2025
  If the main burner of your Groen Kettle comes on but won't stay lit, check the burner ground for a bad wire or connection, replacing it with high-temperature wire if needed. Also, check for low gas supply pressure and consider replacing the ignition control module if necessary. Finally, inspect the ceramic insulator or pilot flame sensor for cracks and replace the flame sensor if it is cracked.
J
joshua57Aug 27, 2025
What to do if the pilot lights, but the main burner will not come on, and spark does not stay on in Groen TDH-CE Mark?
- C
  Cheryl Camacho DVMAug 27, 2025
  If the pilot light ignites, but the main burner doesn't come on and the spark does not stay on in your Groen Kettle, check that the gas pressure meets the control manufacturer’s specifications. If the issue persists, replace the spark ignition module.
J
John SnowAug 25, 2025
What to do if the pilot lights, but the main burner will not come on, and the spark stays on, in Groen TDH-CE Mark Kettle?
- C
  Cheryl RamseyAug 26, 2025
  If the pilot light is on, but the main burner won't ignite and the spark remains on in your Groen Kettle, check these items: * Ensure the sensor cable is securely attached to terminal '1' on the module and to the sensor. * Inspect the sensor ceramic for cracks. * Confirm that the cable is not grounded out; correct any grounding issues. * Check the sensor cable for continuity and the condition of its insulation. * Verify the gas pressure. * Clean the pilot assembly. * Tighten all mechanical and electrical connections.
M
Marisa TerryAug 23, 2025
What to do if the safety valve pops on Groen TDH-CE Mark Kettle?
- P
  Patricia ThompsonAug 25, 2025
  If the safety valve on your Groen Kettle pops, consider the following: * Check for air in the jacket. * Inspect the safety valve. If it pops at pressures below 49 PSIG, replace it. * Verify if the high limit pressure switch is set too high. * Examine the thermostat operation.

Groen TDH-CE Mark Specifications

General

Brand	Groen
Model	TDH-CE Mark
Category	Kettle
Language	English

Related product manuals

Preview: Groen TDH Series

Groen TDH Series

Preview: Groen TDB

Preview: Groen TDB-20

Preview: Groen TDBC-20

Preview: Groen OM-TDB/7

Preview: Groen TDB Series

Groen TDB Series

Preview: Groen AH/1