To Next Page
P
parkerelizabethSep 23, 2025
What to do if Groen Kettle displays HI?
- BbrendaortizSep 23, 2025
If your Groen Kettle displays 'HI', check for loose or broken wires, or a damaged/failed RTD probe.
What to do if Groen Kettle displays HI?
If your Groen Kettle displays 'HI', check for loose or broken wires, or a damaged/failed RTD probe.
What to do if the safety valve pops on Groen TDH Kettle?
If the safety valve on your Groen Kettle pops, consider the following: * Check for air in the jacket. * Inspect the safety valve. If it pops at pressures below 49 PSIG, replace it. * Verify if the high limit pressure switch is set too high. * Examine the thermostat operation.
What to do if the pilot lights, but the main burner will not come on, and the spark stays on, in Groen TDH?
If the pilot light is on, but the main burner won't ignite and the spark remains on in your Groen Kettle, check these items: * Ensure the sensor cable is securely attached to terminal '1' on the module and to the sensor. * Inspect the sensor ceramic for cracks. * Confirm that the cable is not grounded out; correct any grounding issues. * Check the sensor cable for continuity and the condition of its insulation. * Verify the gas pressure. * Clean the pilot assembly. * Tighten all mechanical and electrical connections.
What to do if the pilot lights, but the main burner will not come on, and spark does not stay on in Groen TDH Kettle?
If the pilot light ignites, but the main burner doesn't come on and the spark does not stay on in your Groen Kettle, check that the gas pressure meets the control manufacturer’s specifications. If the issue persists, replace the spark ignition module.
What to do if the main burner comes on but will not stay lit on Groen Kettle?
If the main burner of your Groen Kettle comes on but won't stay lit, check the burner ground for a bad wire or connection, replacing it with high-temperature wire if needed. Also, check for low gas supply pressure and consider replacing the ignition control module if necessary. Finally, inspect the ceramic insulator or pilot flame sensor for cracks and replace the flame sensor if it is cracked.
What to do if Groen Kettle spark is present but the pilot will not light?
If a spark is present but the pilot on your Groen Kettle will not light, ensure that the pilot valve is securely connected to the terminals.
What to do if Groen TDH pilot lights but main burner will not come on and the spark stays on?
If the pilot light on your Groen Kettle lights, but the main burner won't come on and the spark stays on, check for a bad burner ground. Repair with high-temperature wire if necessary.
What to do if Groen Kettle pilot lights but main burner will not come on and spark does not stay on?
If the pilot light on your Groen Kettle lights, but the main burner won't come on and the spark does not stay on, check for 24 V between terminals MV and PV/MV while the pilot is burning. If 24V is not present, replace the ignition control module.
How to fix Groen TDH burners that will not light?
If the burners on your Groen Kettle won't light, ensure that the main gas supply valve is open. The handle should be in line with the gas pipe.
Why is my Groen TDH Kettle heating slowly?
If your Groen Kettle is heating slowly, check for air in the jacket.
General| Type | Tilting Kettle |
|---|---|
| Material | 304 Stainless Steel |
| Jacket Type | Steam Jacketed |
| Controls | Manual or Touchscreen |
| Tilting Mechanism | Manual or Electric |
| Heating Method | Steam |
| Agitator Type | Optional |
| Temperature Control | Thermostatic |
| Applications | Soups, sauces, stews, pasta |
