To Next PageTo Next PageWhat to do if Ground Zero HYDROGEN Amplifier turns off at medium / high volume?
If your Ground Zero Amplifier turns off at medium or high volume, verify that the load impedance of each speaker matches the amplifier's technical specifications.
What to do if Ground Zero HYDROGEN is turning off at medium or high volume?
If your Ground Zero Amplifier is turning off at medium or high volume, check the speaker load impedance. Ensure that proper speaker load impedance recommendations are being observed. Remember that DC resistance and AC impedance may not be the same.
What to do if my Ground Zero HYDROGEN has no audible sound?
If your Ground Zero Amplifier produces no sound, first check if the POW LED is green. If not, verify the protection fuse(s), remote wire connection (in RCA input mode), +24 Volt power supply wire connection, and ground wire connection. If the PRO LED is red, inspect the speaker for shorts or the amplifier for overheating.
Why does my Ground Zero HYDROGEN device not turn on?
If your Ground Zero Amplifier isn't powering on, check the amplifier's power supply by inspecting the power wire and its connections. Also, if using RCA input mode, ensure the remote wire is properly connected to the head unit.
What to do if Status LED turned on red in Ground Zero HYDROGEN Amplifier?
If the status LED on your Ground Zero Amplifier is red, it could indicate that the temperature protection circuit is active or that the speaker wires are shorted/speaker is damaged. Try decreasing the head unit's volume or wait for the unit to cool down. Also, inspect the speaker and wires for shorts and insulate if necessary.
What to do if Ground Zero HYDROGEN Amplifier turns off at medium/high volume?
If your Ground Zero Amplifier shuts down at medium or high volume, verify that each speaker's load impedance matches the amplifier's technical specifications.
How to fix no sound on one channel of Ground Zero Amplifier?
If you're experiencing sound only on one channel of your Ground Zero Amplifier, check the speaker wiring for short circuits or open connections. Additionally, verify the input signal on both RCA leads by reversing the left and right RCA inputs to test the audio input signal.
What to do if the Status LED turned on red on Ground Zero HYDROGEN?
If the status LED on your Ground Zero Amplifier turns red, it indicates that the temperature protection circuit has been activated, or there may be a short in the speaker wires, or the speaker is damaged. To resolve this, either decrease the head unit's volume or wait for the amplifier to cool down. Also, inspect the speaker and wires for any damage and insulate if necessary.
How to troubleshoot no audible sound from Ground Zero HYDROGEN?
If your Ground Zero Amplifier isn't producing any audible sound, first check if the POW LED is green. If not, examine the amplifier's protection fuse(s), the remote wire connection (in RCA input mode), the +12 Volt power supply wire connection, and the ground wire connection. If the PRO LED is red, check for a speaker short or amplifier overheating.
Why my Ground Zero Amplifier device does not turn on?
If your Ground Zero Amplifier doesn't turn on, examine the amplifier's power supply by checking the power wire and connections. Also, if you're using RCA input mode, verify that the remote wire is powered and properly connected to the head unit.
Lists required tools and materials for installation.
Covers drilling safety, wire routing, capacitor use, and volume warnings.
Guidance on planning system expansion and selecting a mounting location.
Covers input level, bass boost, phase shift, and remote control.
Details modes, high pass, and low pass crossover adjustments.
Includes speaker terminals, RCA output, and status LEDs.
Explains the automatic turn-on sequence and thermal shutdown.
Step-by-step guide to setting the audio level for optimal listening.
Illustrates 2, 3, and 4 channel stereo wiring configurations.
Details the trimode wiring setup for subwoofer and speaker integration.
Table listing inductor and capacitor values for 6dB passive crossovers.
Detailed specs including RMS power, damping factor, frequency response, and dimensions.
Provides common symptoms, check points, and cures for amplifier issues.
Details limited warranty terms, return procedures, and exclusions.
Lists required tools and materials for installation.
Covers drilling safety, wire routing, capacitor use, and volume warnings.
Guidance on planning system expansion and selecting a mounting location.
Covers input level, bass boost, phase shift, and remote control.
Details modes, high pass, and low pass crossover adjustments.
Includes speaker terminals, RCA output, and status LEDs.
Explains the automatic turn-on sequence and thermal shutdown.
Step-by-step guide to setting the audio level for optimal listening.
Illustrates 2, 3, and 4 channel stereo wiring configurations.
Details the trimode wiring setup for subwoofer and speaker integration.
Table listing inductor and capacitor values for 6dB passive crossovers.
Detailed specs including RMS power, damping factor, frequency response, and dimensions.
Provides common symptoms, check points, and cures for amplifier issues.
Details limited warranty terms, return procedures, and exclusions.
General| Brand | Ground Zero |
|---|---|
| Model | HYDROGEN SERIES |
| Category | Amplifier |
| Language | English |
