What does W20 Measurement process incomplete mean for HACH LANGE ORBISPHERE 6110?
If your HACH LANGE Measuring Instruments display warning W20, it means the measurement process is incomplete because of insufficient initial package pressure. This can happen if the pressure in the package is too low to continue with a measurement, so you should restart the measurement with another package.
What to do if HACH LANGE ORBISPHERE 6110 Measuring Instruments show E1 Emergency STOP error?
If you see error E1 on your HACH LANGE Measuring Instruments, it means the emergency STOP button has been pushed. To fix this, release the emergency STOP button by turning it clockwise. If necessary, initialize the motor.
Why HACH LANGE Measuring Instruments show E100 Ultrasound error?
If your HACH LANGE Measuring Instruments display error E100, it indicates an ultrasound error. This can happen because the ultrasound power supply is OFF, so you should check the ultrasound power supply. It can also happen if the emergency STOP button is not released, so you should release the emergency STOP button by turning it clockwise. Finally, too much water in the ultrasound generator can cause this error, so remove any excess water.
What causes E2 Motor error on HACH LANGE ORBISPHERE 6110?
If your HACH LANGE Measuring Instruments display error E2, it indicates a motor error. This can happen if the measuring head has missed an obstacle, so you should initialize the motor. This can also happen if the emergency STOP button pushed if the motor is moving.
What to do if HACH LANGE ORBISPHERE 6110 show E400 error?
If you are seeing error E400 on your HACH LANGE Measuring Instruments, it means there was a problem initializing the motor displacement, and the measurement was aborted. To solve this, turn the instrument off and restart it.
Why HACH LANGE ORBISPHERE 6110 show E4 error?
If your HACH LANGE Measuring Instruments display error E4, it means the front door has been opened, stopping the measurement process. This can happen if the front door has been opened before the end of the measurement process, so you should close the front door. It can also happen if the front door is not closed properly, so you should control the front door mechanism.
What does W80 Measurement process incomplete mean for HACH LANGE Measuring Instruments?
If your HACH LANGE Measuring Instruments display warning W80, it means the measurement process is incomplete because of insufficient package pressure during the ultrasound stage. This can happen if the measured pressure is too low to compute the second phase of the measurement, so you should check foam intrusion in the gas path.
What to do if HACH LANGE ORBISPHERE 6110 show W40 Spontaneous degassing warning?
If your HACH LANGE Measuring Instruments display warning W40, it means there was spontaneous degassing... This can happen if a spontaneous degassing is detected at the end of the first expansion, so you should restart the measurement with another package.
Why HACH LANGE ORBISPHERE 6110 show E40 Check gas supply error?
If your HACH LANGE Measuring Instruments display error E40, it means to check the gas supply, so you should check the purge gas pressure because before filling the reference volume, the pressure is lower than 1.5 bar.
What causes E20 Not enough pressure error on HACH LANGE Measuring Instruments?
If your HACH LANGE Measuring Instruments display error E20, it means there is not enough pressure in the system and the measurement process has been canceled. This can happen because of a problem of flow regulation during the measurement, so you should check the purge gas pressure and change the Goretex filter. It can also happen if the gas path is partially or totally blocked, so you should control the antifoam injection.
Covers hazard symbols, safety precautions, specific warnings, and service policies.
Detailed specifications for analysis range, units, operating limits, enclosure, and compliance.
Guides through pre-installation, physical installation, and post-installation steps.
Details the automatic component check performed at startup and user login procedures.
Procedures for defining units, resolutions, package parameters, and formulas.
Step-by-step guides for calibrating barometric, pressure, temperature, CO2, flow, and O2 sensors.
Lists error codes, warning messages, causes, solutions, and startup LED meanings.
Common measurement issues, their explanations, and troubleshooting steps.
General| Parameter | Dissolved Oxygen, Ozone, Hydrogen Peroxide |
|---|---|
| Accuracy (Dissolved Oxygen) | ± 0.1 mg/L |
| IP Rating | IP65 |
| Range (Dissolved Oxygen) | 0 to 50 mg/L |
| Range (Ozone) | 0-20 mg/L |
| Range (Hydrogen Peroxide) | 0 - 2 ppm; 0 - 20 ppm |
| Response time (t90) | < 60 seconds |
| Operating temperature | 0 to 50 °C |
| Operating pressure | 0 to 6 bar |
| Wetted materials | Stainless steel, silicone |
| Sensor type | Optical |
| Communication | RS-485 |
| Display | No |
| Outputs | 4-20 mA, Digital |
| Type | Portable sensor |
To Next Page
