Haier ADH071M3ERG - Page 226

224
Smart Power
Difference between the Function of the Master Wired Controller and Slave Wired Controller
Comparison
item
Master
wired
controller
Slave wired controller
Function
All
functions
are
available
1. ON/OFF, Mode, Fan Speed, Temp.
Setting, Swing, Energy Saving, Clock
function, Heat Reclaim Ventilation
function, Mode Setting, Screen
Saving and Child Lock are available
2.Cancel the lter cleaning icon
3.Look up the detailed parameter and
malfunction code
Initialization
(1)The wired controller will display all the icons after powering on or reset, then get into the initializing process. The
controller will display in sequence as follows:
(the top-left corner) → (the top-right corner) → →
(the top-left corner), the green LED ashes all the time until the initialization ends.
(2) If the wired controller can’t be communicated with the indoor PCB normally after powering on, the initialization
will be nished in 4 minutes, and then the communication malfunction can be checked from the malfunction inquiry
function.
Screen Saving
(1) In the state of off and non screen saving, keep pressing
and for 5s to set screen saving time, which will
be shown after the top-right colon 88 statically. Press Up/Down key to adjust screen saving time and press key
to conrm.
(2) Screen saving time should be 0s(backlight always on), 15s, 30s, 60s, default value is 15s. If it is not the rst
time of entering, it will display the screen saving time adjusted last time.
(3) In the process of changing screen saving time, press ON/OFF key to quit screen saving time setting function, it
will recover to screen saving time before adjustment and start-up the unit.
Note:
When controlling Fresh Air unit, the controller main interface will not display Up/Down key in normal state. When in
screen saving setting, press Time key rst to display Up/Down key at the main interface, and then press together
Time and Down key to enter screen saving time setting.
Clock Function
(1) 24-hour system is used, and at rst time of powering on, it will display default 12:00.
(2) When rst powering on wired controller, will be displayed on the wired controller interface, clock time
can be adjusted within 10s. At the same time, clock icon and minute-place of time will ash, meaning the current
time can be adjusted. Press Up/Down key to adjust minute-place with ashing of clock icon and no ashing of
minute-place. Press Time key to shift to hour-place, and then press Up/Down key to adjust hour-place with ashing
of clock icon and no ashing of hour-place. After adjustment, clock icon and hour-place will ash and press key
to conrm and clock icon and time will display statically.
(3) Press Time key for 5s to enter clock setting function. It will show after rst powering on (if not rst time
of powering on, clock time is the memorized time), with clock icon and minute-place ashing, meaning current time
can be adjusted. Press Up/Down key to adjust minute-place with ashing of clock icon and no ashing of minute-
place. Press Time key to shift to hour-place, and then press Up/Down key to adjust hour-place with ashing of
clock icon and no ashing of hour-place. After adjustment, clock icon and hour-place will ash and press key to
conrm and clock icon and time will display statically.
(4) Clock time adjustment: when adjusting time, press one time to reduce one minute/hour while press one
time to add one minute/hour. Keep pressing or key to accelerate time adjustment, with 2 times/s change after 1 s,
10 times/s change after 5s. After 10s, it will change by 10 minutes and frequency is 10 times/s.
(5) In the process of time adjustment, if there is no operation for 10s, it will quit and restore previous state.
(6) In the process of time adjustment, press ON/OFF key to quit clock setting function and execute turning on/off
operation at the same time.