Why won't my Haier HW100-BP14636 start?
If your Haier Washing machine won't start, here are a few things to check: * Make sure the program has been started. * Ensure the door is properly closed. * Verify the machine is switched on. * Check for a power failure. * Deactivate the child lock if it's enabled.
Why is my Haier HW100-BP14636 not filling with water?
If your Haier Washing machine isn't filling with water, try the following: * Check that the water tap is open. * Inspect the inlet hose for kinks. * Unblock the inlet hose filter. * Check the water pressure to ensure it's at least 0.03 MPa. * Ensure the door is properly closed. * Ensure the water supply.
How to fix drainage failure in Haier HW100-BP14636 Washing machine?
If your Haier Washing machine is not draining, consider the following: * Unblock the drain hose. * Clean the pump filter. * Make sure that drain hose is properly installed and its end is not higher than 100 cm above floor level.
Why is my Haier HW100-BP14636 Washing machine vibrating so much?
If your Haier washing machine is vibrating excessively during spinning, the causes might be: * Not all transportation bolts have been removed. Remove all transportation bolts. * Appliance has no solid position. Ensure solid ground and a leveled position. * Machine load is not correct. Check load weight and balance.
Why is the spinning cycle failing on my Haier HW100-BP14636 Washing machine?
If the spinning cycle fails on your Haier Washing machine, it might be due to an unbalance of laundry. Check the machine load and laundry, then run a spinning program again.
How to improve unsatisfactory washing results with my Haier HW100-BP14636 Washing machine?
If you're getting unsatisfactory washing results with your Haier Washing machine: * Select another program if the degree of pollution does not agree with selected program. * Choose the detergent according to the degree of pollution and according to manufacturer specifications if the detergent quantity was not sufficient. * Reduce loading if the maximum load has been exceeded. * Loose the laundry if the laundry was unevenly distributed in the drum.
How to remove washing powder residues from laundry in my Haier Washing machine?
If you find washing powder residues on your laundry after washing with your Haier Washing machine: * Perform an extra rinse, insoluble particles of detergent can remain as white spots on the laundry. * Try to brush the points from the dry laundry. * Choose another detergent.
What to do if my Haier HW100-BP14636 shows UNB error?
If your Haier Washing machine displays an 'UNB' error, it indicates an unbalanced load. To resolve this: * Check and balance the laundry load in the drum. * Reduce the load if necessary.
What does E1 error mean on my Haier HW100-BP14636 Washing machine?
If your Haier Washing machine displays an 'E1' error, it means there's a drainage issue where water isn't fully drained within 6 minutes. Try cleaning the pump filter and checking the drain hose installation.
Why is my Haier Washing machine draining while filling?
If your Haier Washing machine is draining while it's filling, it could be due to: * The height of the drain hose being below 80 cm. Make sure that drain hose is properly installed. * The drain hose end reaching into the water. Make sure the drain hose is not in water.
General| Load Capacity | 10 kg |
|---|---|
| Loading type | Front Load |
| Spin Speed | 1400 RPM |
| Energy Rating | A+++ |
| Display Type | LED |
| Number of Programs | 16 |
| Noise level washing | 53 dB |
| Noise level spinning | 72 dB |
| Color | White |
| Inverter Motor | Yes |
| Child Lock | Yes |
| Delay Start | Yes |
| Quick Wash | Yes |
| Dimensions (HxWxD) | 85 cm x 59.8 cm x 60 cm |
| Water Consumption | 52 L |
Guidelines for routine maintenance and cleaning of the appliance.
Instructions for proper and safe installation of the washing machine.
Defines the proper and intended use of the washing machine.
Initiates, pauses, or resumes the washing program.
How to initiate the selected wash cycle.
Procedures for pausing, cancelling, or restarting a wash cycle.
Procedure for cleaning the drain pump filter.
Explanation of codes displayed on the appliance for status information.
Solutions for common problems indicated by error codes on the display.
Guidance for resolving issues that do not trigger display error codes.
Initial steps and checks before installing the appliance.
Instructions for removing bolts used during transportation.
Steps to ensure the appliance is level for optimal performance and stability.
Instructions for connecting the drain hose to various outlets.
How to connect the appliance to the cold water supply.
Steps for safely connecting the appliance to the mains power supply.
To Next Page
