Why won't my Haier HW80-BP14636 Washing machine start?
If your Haier Washing machine won't start, here are a few things to check: * Make sure the program has been started. * Ensure the door is properly closed. * Verify the machine is switched on. * Check for a power failure. * Deactivate the child lock if it's enabled.
Why is my Haier HW80-BP14636 not filling with water?
If your Haier Washing machine isn't filling with water, try the following: * Check that the water tap is open. * Inspect the inlet hose for kinks. * Unblock the inlet hose filter. * Check the water pressure to ensure it's at least 0.03 MPa. * Ensure the door is properly closed. * Ensure the water supply.
How to fix drainage failure in Haier HW80-BP14636 Washing machine?
If your Haier Washing machine is not draining, consider the following: * Unblock the drain hose. * Clean the pump filter. * Make sure that drain hose is properly installed and its end is not higher than 100 cm above floor level.
Why is my Haier HW80-BP14636 Washing machine vibrating so much?
If your Haier washing machine is vibrating excessively during spinning, the causes might be: * Not all transportation bolts have been removed. Remove all transportation bolts. * Appliance has no solid position. Ensure solid ground and a leveled position. * Machine load is not correct. Check load weight and balance.
Why is the spinning cycle failing on my Haier HW80-BP14636?
If the spinning cycle fails on your Haier Washing machine, it might be due to an unbalance of laundry. Check the machine load and laundry, then run a spinning program again.
How to improve unsatisfactory washing results with my Haier Washing machine?
If you're getting unsatisfactory washing results with your Haier Washing machine: * Select another program if the degree of pollution does not agree with selected program. * Choose the detergent according to the degree of pollution and according to manufacturer specifications if the detergent quantity was not sufficient. * Reduce loading if the maximum load has been exceeded. * Loose the laundry if the laundry was unevenly distributed in the drum.
How to remove washing powder residues from laundry in my Haier Washing machine?
If you find washing powder residues on your laundry after washing with your Haier Washing machine: * Perform an extra rinse, insoluble particles of detergent can remain as white spots on the laundry. * Try to brush the points from the dry laundry. * Choose another detergent.
What to do if my Haier HW80-BP14636 shows UNB error?
If your Haier Washing machine displays an 'UNB' error, it indicates an unbalanced load. To resolve this: * Check and balance the laundry load in the drum. * Reduce the load if necessary.
What does E1 error mean on my Haier HW80-BP14636 Washing machine?
If your Haier Washing machine displays an 'E1' error, it means there's a drainage issue where water isn't fully drained within 6 minutes. Try cleaning the pump filter and checking the drain hose installation.
Why is my Haier HW80-BP14636 draining while filling?
If your Haier Washing machine is draining while it's filling, it could be due to: * The height of the drain hose being below 80 cm. Make sure that drain hose is properly installed. * The drain hose end reaching into the water. Make sure the drain hose is not in water.
Important safety checks and handling instructions before operating the appliance for the first time.
Rules and recommendations for safe daily operation and usage of the washing machine.
Table detailing available wash programmes, their load capacity, temperature, and functions.
Guidelines on sorting, checking, and preparing clothes before washing.
Proper techniques for loading laundry into the drum to ensure efficiency and prevent damage.
Guidance on choosing and using the correct type and amount of detergent and softener.
How to start, pause, interrupt, and manage wash programmes effectively.
Steps after washing, including door unlocking, energy saving, and buzzer settings.
Solutions for common problems indicated by error codes E1, E2, E4, and E8 on the display.
Solutions for specific error codes like F3, F4, F7, FA, FC2, and Unb.
Solutions for common issues that do not trigger error codes on the display.
Detailed instructions for connecting the drain hose to sinks or waste pipes.
How to connect the water inlet hose to the appliance and the water tap.
Procedures for safely connecting the washing machine to the power supply.
General| Door hinge | - |
|---|---|
| Control type | Rotary |
| Loading type | Front-load |
| Product color | White |
| Built-in display | Yes |
| Appliance placement | Freestanding |
| Drum capacity | 8 kg |
| Wi-Fi controlled | No |
| Maximum spin speed | 1400 RPM |
| Noise level (spin) | - dB |
| Package width | 650 mm |
| Package height | 890 mm |
| Package weight | 72000 g |
| Energy consumption washing per cycle | - kWh |
Weight and Dimensions| Depth | 550 mm |
|---|---|
| Width | 595 mm |
| Height | 850 mm |
| Weight | 70000 g |
To Next Page
