Why is there strong vibration while spinning in my Haier HWD100-B14979 Washer/Dryer?
If your Haier Washer/Dryer is experiencing strong vibrations during spinning, make sure all transportation bolts have been removed, the appliance is on solid, level ground, and the machine load is correct. Remove any remaining transportation bolts, ensure the appliance is on solid ground and in a leveled position and check the load weight and balance.
Why my Haier Washer/Dryer appliance will not be filled with water?
If your Haier Washer/Dryer appliance won't fill with water, check the water tap, inlet hose (ensure it's not kinked), and inlet hose filter (unblock if necessary). Also, verify that the water pressure is at least 0.03 MPa, the door is properly closed, and the water supply is functional. The causes may be no water, a kinked inlet hose, a blocked inlet hose filter, insufficient water pressure, an improperly closed door or a water supply failure.
What to do for lock error in Haier HWD100-B14979?
If your Haier Washer/Dryer displays a lock error, ensure that the door is properly shut.
Why is spinning failing in my Haier HWD100-B14979 Washer/Dryer?
If spinning fails in your Haier Washer/Dryer, it may be due to an unbalance of laundry. Check the machine load and laundry, then run a spinning program again.
What to do if my Haier HWD100-B14979 Washer/Dryer appliance fails to operate?
If your Haier Washer/Dryer appliance isn't starting, ensure the program is selected and started, the door is properly closed, the machine is switched on, there's no power failure, and the child lock is deactivated. The causes may be that the program hasn't started, the door isn't closed properly, the machine hasn't been switched on, there's a power failure, or the child lock is activated.
Why is my Haier Washer/Dryer draining while being filled?
If your Haier Washer/Dryer is draining while filling, it might be because the drain hose is positioned lower than 80 cm or the drain hose end is submerged in water. Ensure the drain hose is properly installed and is not in water.
How to fix a drainage error in my Haier Washer/Dryer?
If the Haier Washer/Dryer displays a drainage error where water isn't fully drained within 6 minutes, clean the pump filter and check the drain hose installation.
How to resolve drainage error during i-Refresh programme in Haier HWD100-B14979 Washer/Dryer?
If your Haier Washer/Dryer shows a drainage error where water isn't fully drained within 1 minute during the i-Refresh program, clean the pump filter and check the drain hose installation.
How to troubleshoot drainage failure in Haier HWD100-B14979 Washer/Dryer?
If your Haier Washer/Dryer is experiencing drainage failure, it could be due to a blocked drain hose or pump filter, or the drain hose end being higher than 100 cm above floor level. Unblock the drain hose, clean the pump filter, and ensure the drain hose is properly installed.
What to do if water level not reached after 8 minutes in Haier HWD100-B14979 Washer/Dryer?
If the water level isn't reached after 8 minutes in your Haier Washer/Dryer, ensure the tap is fully opened and water pressure is normal. Also, check the drain hose installation, as it may be self-syphoning.
General safety checks and precautions before operating the appliance for the first time.
Essential safety guidelines for using the washing machine during everyday operation.
Guidelines for safe installation and intended use of the washing machine.
Table detailing programmes, load capacity, temperature, spin speed, and functions.
Steps for switching on, selecting programmes, and starting/interrupting cycles.
Solutions for common problems indicated by display codes.
Resolving issues without specific display codes, like operational failures.
Unpacking the appliance and removing transportation bolts.
Connecting the drain hose to a sink or waste pipe.
Steps for connecting the water supply and the electrical power.
General| Capacity | 10 kg (washing) / 6 kg (drying) |
|---|---|
| Spin Speed | 1400 RPM |
| Energy Efficiency | A |
| Loading Type | Front Loading |
| Dimensions | 850 x 600 x 600 mm |
To Next Page