Haier XQB50-10 User Manual (English)

Other manuals for Haier XQB50-10

User Manual20 pages

Service Manual18 pages

Questions and Answers:

A
Alexis CarlsonAug 14, 2025
Why Haier XQB50-10 Washer won't wash, act or spin?
- S
  Shannon RobinsonAug 14, 2025
  Your Haier Washer might not wash, act, or spin due to several reasons: - There could be a power failure, or the power plug might be loose. Make sure the power is on and the plug is inserted tightly. - The water level might not be reaching the set level. Ensure affusion to the set water level. - The top lid might not be closed properly. Ensure the top lid is closed. - The laundries might not be put orderly. Put the laundries orderly.
A
alyssa18Aug 18, 2025
How to fix Haier XQB50-10 when it doesn't drain or drains slowly and shows E1?
- S
  Sheila RiveraAug 18, 2025
  If your Haier Washer isn't draining properly and the nixie tube shows "E1", buzzing, it could be due to these reasons: - The drain hose might be placed incorrectly. Put down the drain hose and open and close the top lid once. - The drain hose might be blocked by foreign material. Clean the foreign material and open and close the top lid once.
C
Crystal SmithAug 21, 2025
Why is there an abnormal sound inside my Haier XQB50-10?
- C
  Christina PhillipsAug 21, 2025
  An abnormal sound inside your Haier Washer could be due to: - The machine not being level. Level the machine properly. - The laundries being placed unevenly during spinning. Re-order the laundries.
J
jessecurryAug 25, 2025
Why does the water faucet leak on my Haier XQB50-10 Washer?
- B
  Barbara HerreraAug 25, 2025
  If the water faucet on your Haier Washer is leaking, it could be because the jointer screw of the water inlet hose is loose or twisted awry. Fasten the jointer screw properly.
G
garygomezAug 28, 2025
What to do if Haier XQB50-10 is not filling with water or fills slowly and shows E4?
- C
  Christopher SolomonAug 28, 2025
  If your Haier Washer is not filling with water or is filling slowly and the nixie tube indicates "E4", it could be due to the following reasons: - The water tap might not be open. Open the water tap and push the "Start/Pause" button. - The water inlet valve might be blocked. Clean the water inlet valve and push the "Start/Pause" button. - The water pressure might be too low. Wait for normal water pressure before use.
L
laneannAug 31, 2025
Why Haier Washer stops spinning, shows E3, and buzzes?
- T
  thernandezAug 31, 2025
  If your Haier Washer stops spinning, displays "E3" on the nixie tube, and buzzes, it could be because: - The laundries are not placed evenly. Re-order the laundries and close the top lid. - The machine is not level. Level the machine in the right position and open and close the top lid once.
B
Brooke GomezSep 3, 2025
What to do if Haier Washer pauses during spin, shows E2 and buzzing?
- Q
  qrichardsSep 3, 2025
  If your Haier Washer pauses during the spin cycle and the nixie tube indicates "E2", buzzing, it is likely because the top cover is open. Close the top lid.
R
Robert WrightSep 6, 2025
How to stop buzzing and E0 error on Haier XQB50-10?
- L
  Latasha LeeSep 6, 2025
  If your Haier Washer is buzzing and the nixie tube indicates "E0" upon reservation start, it means the top lid is not closed. Close the top lid.
C
Carol ArmstrongSep 10, 2025
What to do if Haier XQB50-10 Washer has poor or no waterfall flow?
- G
  goliverSep 12, 2025
  If your Haier Washer has poor or no waterfall flow, it might be because the nozzle is choked with foreign bodies. Remove the foreign bodies.