EasyManua.ls Logo

Hakko Electronics B5166 User Manual

Hakko Electronics B5166
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
取扱説明書
B5256
N
2
NOZZLE CHANGER
組立て
セット内容
N2ノズルチェンジャーはこて台の左右
どちらにも取り付けられます。
ノズル組品に溝が付いています。
溝部分をノズルチェンジャーの金具に引っ掛けます。
こて部を引っ張るとノズル組品がこて部から外れます。
こて部の軸に沿って
まっすぐ引き抜いて
ください
使用方法
注意
使用直後のノズル組品は高温となりますのでやけどにご注意ください。
通電状態でこて部を長時間ノズルチェンジャーに置かないように注意して
ください。
2019.8
MA03107XZ190820
セムスねじP2
N2ノズルチェンジャー
セムスねじP2(M3×6)
取扱説明書
.................................1
..............................2
......................................................1
N2ノズル
チェンジャー
取扱説明書
THERMAL WIRE STRIPPER
FT-802
〒556-0024大阪市浪速区塩草2丁目4番5号
:( 06)6561-1574(代)F :( 06)6568-0821
https://www.hakko.com
© 2019 HAKKO Corporation. All Rights Reserved.
OVERSEAS AFFILIATES
U.S.A.: AMERICAN HAKKO PRODUCTS, INC.
TEL: (661) 294-0090 FAX: (661) 294-0096
Toll Free (800) 88-HAKKO
4 2 5 5 6
http://www.HakkoUSA.com E-mail: Support@HakkoUSA.com
SINGAPORE: HAKKO PRODUCTS PTE., LTD.
TEL: 6748-2277 FAX: 6744-0033
http://www.hakko.com.sg E-mail: sales@hakko.com.sg
HONG KONG: HAKKO DEVELOPMENT CO., LTD.
TEL: 2811-5588 FAX: 2590-0217
http://www.hakko.com.cn E-mail: info@hakko.com.hk
Please access to the following address for the other Sales affiliates.
https://www.hakko.com
HEAD OFFICE
4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN
TEL: +81-6-6561-3225 FAX: +81-6-6561-8466
https://www.hakko.com E-mail: sales@hakko.com
Question and Answer IconNeed help?

Do you have a question about the Hakko Electronics B5166 and is the answer not in the manual?

Hakko Electronics B5166 Specifications

General IconGeneral
BrandHakko Electronics
ModelB5166
CategoryPower Tool
LanguageEnglish

Summary

Packing List

Included Components

Lists the N2 nozzle changer, SEMS screw P2, and instruction manual.

Assembly and Setup

Mounting Location

The nozzle changer can be attached to either the left or right side of the iron stand.

Operation and Safety

Safety Precautions

Be careful of burns; the nozzle assembly is hot after use. Avoid leaving the soldering iron in the changer when powered on.

Nozzle Assembly Removal

Engage the groove on the nozzle assembly with the metal fitting and pull straight out along the iron's axis.

Related product manuals