Hakko Electronics FR-301

To Next Page

OVERSEAS AFFILIATES

U.S.A.: AMERICAN HAKKO PRODUCTS, INC.

TEL: (661) 294-0090 FAX: (661) 294-0096

Toll Free (800)88-HAKKO

4 2 5 5 6

http://www.hakkousa.com

HONG KONG: HAKKO DEVELOPMENT CO., LTD.

TEL: 2811-5588 FAX: 2590-0217

http://www.hakko.com.hk

E-mail:info@hakko.com.hk

SINGAPORE: HAKKO PRODUCTS PTE., LTD.

TEL: 6748-2277 FAX: 6744-0033

http://www.hakko.com.sg

E-mail:sales@hakko.com.sg

Please access to the following address for the other Sales affiliates.

http://www.hakko.com

HEAD OFFICE

4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN

TEL:+81-6-6561-3225 FAX:+81-6-6561-8466

http://www.hakko.com E-mail:sales@hakko.com

2017.9

MA02939XZ170928

1. PACKING LIST AND PART NAMES

Please check to make sure that all items listed below are included in the package.

2. SPECIFICATIONS

Part name HAKKO FR-301

Nozzle to ground

potential

<2 mV

Power supply

100V-98W (50/60Hz), 110V-122W

(50/60Hz), 120V-140W (60Hz),

220V-100W (50/60Hz), 230V-110W

(50/60Hz), 240V-120W (50/60Hz)

Vacuum generator Diaphragm pump

Vacuum pressure 81 kPa (610 mmHg)

Suction ow 11 L/min

Temperature range 350

500 °C (660 to 930 °F) Dimensions 215 (W) × 226 (H) mm/8.3 × 8.9 in.

Nozzle to ground

resistance

<2 Ω Weight

0.52 kg/1.1 lb. with ø1.0 mm

[0.04 in] nozzle

• The temperature was measured using the HAKKO FG-101 Station Tester.

• Specications and design are subject to change without notice.

HAKKO FR-301 .....................................................1

Ceramic paper lter (L) .........................................2

Nozzle wrench ........................................................ 1

Pre-lter ..................................................................1

Iron holder ..............................................................1

Cleaning Pin (for ø1.0mm [0.04 in] nozzle) ............1

Cleaning Pin (for Heating Element) ........................1

Instruction manual (This manual) ...........................1

Desoldering Tool

Instruction Manual

Thank you for purchasing the HAKKO FR-301 Desoldering Tool.

Please read this manual before operating the HAKKO FR-301.

Please keep this manual readily accessible for reference.

HAKKO FR-301

Ceramic paper lter (L)

Iron holder

Nozzle wrench

Cleaning Pin

(for ø1.0mm [0.04 in]

nozzle)

Cleaning Pin

(for Heating Element)

Pre-lter

Main Page

Need help?

Do you have a question about the Hakko Electronics FR-301 and is the answer not in the manual?

Summary

PACKING LIST AND PART NAMES

SPECIFICATIONS

WARNINGS AND CAUTIONS

WARNING

Critical safety warnings related to hot surfaces, electrical hazards, and proper usage.

CAUTION

Important precautions to prevent damage, injury, or malfunction during operation.

PART NAMES

OPERATION

Preparation

Steps to prepare the HAKKO FR-301 for use, including power connection and initial setup.

Desoldering

Detailed instructions for the desoldering process, including nozzle placement and trigger use.

Cleaning

Procedures for cleaning the tool's components like the nozzle, heating core, and filter.

Temperature Setting

Guidance on adjusting the desoldering tool's temperature for different types of circuit boards.

MAINTENANCE

General Guide to Replacement Parts

Information on identifying when desoldering tool parts need replacement based on signs of wear.

Replacing Parts

Instructions for replacing key components like the nozzle and filter pipe assembly.

Pump Maintenance

Steps for cleaning the pump assembly, including the valve plate, fixing plate, and pump head.

Replacing the Heating Element

Guide for replacing the heating core and subsequent nozzle temperature calibration.

TROUBLESHOOTING

Calibrating Temperature

Procedure for calibrating the desoldering tool's nozzle temperature after replacement or adjustment.

Problem Cause and Procedure

Table detailing common issues, their causes, and recommended solutions for the desoldering tool.

REPLACEMENT PARTS;OPTION

Nozzle Styles

Visual guide to the different nozzle types and their dimensions available for the tool.