2 Specications
433MHz TRANSMITTERS & RECEIVER
USER’S GUIDE
DIGITAL TRANSMITTERS AND RECEIVER WITH SEQUENCING FUNCTION
1 Description
DESCRIPTION SPECIFICATION
FREQUENCY 433 MHz
EMITTED RADIO POWER -28.7 dBm (Transmitter)
POWER CONSUMPTION 3mA (Transmitter) 30mA (Receiver)
INPUT VOLTAGE 12 to 24 VAC/DC (Receiver)
CONTACT RATING 1.0 A @ 30 VDC / 0.3 A @ 60 VDC
0.5 A @ 125 VAC
OPERATING TEMPERATURE 14ºF TO 131ºF (-10ºC TO 55ºC)
MAX No. OF PROGRAMMED
UNITS PER RECEIVER
100 TRANSMITTERS
LEDs Receiver Learn
Relay Activation
RED
BLUE
DIMENSIONS Transmitter
Receiver
2 3/4” X 1 3/8” X 9/16” (70mm x 35mm x 14mm)
2 3/4” x 2 1/8” x 1” (70mm x 55mm x 25mm)
CERTIFICATIONS FCC, IC,
75.5092.09 EN 20160623 Page 1 of 4
The 433MHz Series Transmitters and Receiver are ideal for the wireless activation and/or sequencing of automatic doors. The transmitters are available
in hand-held or pushplate styles and they transmit a unique rolling code each time the transmitter is activated (thus providing a secure door opening
signal). The transmitter PN: 10TD433PB9V is powered by a 9-volt battery whereas all other transmitters are powered by a 3 volt battery and all
illuminate a Red LED when activated.
Since receivers can be individually programmed, multiple receivers can be programmed differently thus allowing for sequencing in multiple applications.
Upon activation (pushplate / transmitter), all receivers will acquire the signal at the same time; however, each receiver will respond according to
their programming. Those receivers programmed with NO DELAY will active immediately upon receiving the transmitter signal. Those receivers
programmed with a DELAY will activate at the end of their pre-determined time delay set by the potentiometer. The use of multiple receivers will allow
for the uninterrupted pace or hands free operations through a pair of doors upon initial activation.
10TD433HH
ONE BUTTON
10TD433HH2
TWO BUTTON
10TD433HH3
THREE BUTTON
10TD433HH4
FOUR BUTTON
10TD433PB3V
3V w / LEADS
10TD433PB9V
9V w / LEADS
FCC ID#: G9B-10TD433HH4 IC ID#: 4680A-10TD433HH4
3 Precautions
This wireless receiver is not intended to be used DIRECTLY with maglocks or electric strikes due to possible damage caused by
inductive load kickback. Instead, this wireless receiver should be used to trigger a logic module (Br3) or isolation relay which then
triggers the maglock or electric strike.
Shut off all power going to work area before attempting any wiring procedures.
Maintain a clean & safe environment when working in public areas.
To remain in compliance with Part 15.231, do not operate transmitter (hold down button ) for longer than 5 seconds.
Constantly be aware of pedestrian trafc around the area.
Always stop pedestrian trafc through the doorway when performing tests that may result in unexpected- reactions by the door.
ESD: Circuit boards are vulnerable to damage by electrostatic discharge. Before handling ensure you dissipate your body’s charge.
Always check placement of components before powering up so that moving parts will not catch any wires or cause damage to
equipment.
Ensure compliance with all applicable safety standards (i.e. ANSI A156.10 / 19) upon completion of installation.
DO NOT attempt any internal repair of the components. All repairs and/or component replacements must be performed by BEA,
Inc. Unauthorized disassembly or repair:
1. May jeopardize personal safety and may expose one to the risk of electrical shock.
2. May adversely affect the safe and reliable performance of the product resulting in a voided warranty.
ANTENNA WIRE
DIP
SWITCH
LEARN WITH
DELAY BUTTON
LEARN
W/O DELAY
BUTTON
DELAY
POTENTIOMETER
(Time Adjustment)
TERMINAL
STRIP
RED LED
BLUE LED
To Next Page
Need help?
General