HM8130E/0405/ce · Subject to alterations · © HAMEG GmbH · ® Registered Trademark · DQS-certified in accordance with DIN EN ISO 9001:2000, Reg.-No.: DE-071040 QM
HAMEG GmbH · Industriestr. 6 · D-63533 Mainhausen · Tel +49 (0) 6182 800 0 · Fax +49 (0) 6182 800 100 · www.hameg.com · info@hameg.com
www.hameg.com
10 MHz Function Generator HM8130
Valid at 23 degrees °C after a 30 minute warm-up period
Frequency
Range: 10 mHz to 10 MHz
Resolution: 5-digit, max. 10 mHz
Display: 5-digit LED
Accuracy: ±(1 digit + 5 mHz)
Temperature coefficient: 0.5ppm/°C
Aging: 2ppm/year
Waveforms
Sine wave
Frequency range: 10 mHz to 10 MHz
Amplitude: 0 - 20 V
pp
(open circuit)
Distortion: to 500 kHz: ‹ 0.5 %
500 kHz-3 MHz: ‹ 1 %
3 MHz-10 MHz: ‹ 3 %
Square wave
Frequency range: 10 mHz to 10 MHz
Amplitude: 0 - 20 V
pp
(open circuit)
Rise/fall time: ‹10ns
Overshoot: ‹ 5 % (V
out
≥ 200 mV)
Symmetry: 50% ±(5%+10ns)
Pulse
Frequency range: 10 mHz to 5 MHz
Amplitude: 0...+10 V and 0...-10 V
Rise/fall time: ‹10ns
Pulse width: 100 ns to 80 s
Duty cycle: max. 80 %
Saw thooth
Frequency range: 10 mHz to 500 kHz
Amplitude: 0 - 20 V
pp
(open circuit)
Linearity: better than 1 %
Triangle
Frequency range: 10 mHz to 2 MHz
Amplitude: 0 - 20 V
pp
(open circuit)
Linearity: better than 1 %
Arbitrary generator
Frequency range: 10 mHz to 100 kHz
Amplitude: max. 20 V
pp
(open circuit)
Sampling rate: 40MSa/s
Resolution:X: 1024 (10bit); Y: 4096 (12 bit)
Inputs
Gate/trigger: BNC connector
Impedance: 5 kΩ II 100 pF; protected up to ± 30 V
AM-IN: amplitude modulation, BNC connector
Impedance: 10 kΩ; protected up to ± 30 V
Outputs
Signal output: (BNC connector)
short-circuit proof; ext. voltage max. ± 15 V
Impedance: 50 Ω
Output voltage: Range 1: 2.1 - 20 V
pp
(open circuit)
Range 2: 0.21 - 2.0 V
pp
(open circuit)
Range 3: 20 - 200 mV
pp
(open circuit)
Resolution: Range 1: 100 mV
Range 2: 10 mV
Range 3: 1 mV
Setting accuracy: Range 1: ± 2 %
(1kHz) Range 2: ± 3 %
Range 3: ± 4 %
3 % additional for pulse and square wave
Frequency response: ‹ 100 kHz: ± 0.2 dB
100 kHz - 2 MHz: ± 0.5 dB
2 MHz - 10 MHz: + 0.5 dB /- 3 dB
Offset error: ± 50 mV (Range 3)
Display: 2
1
/
2
digit (LED)
DC offset
Output voltage: Range 1: -7.5...+7.5 V (open circuit)
Range 2: -0.75...+0.75 V (open circuit)
Range 3: -75...+75 mV (open circuit)
Trigger output (BNC connector)
Ramp: 0 to 5 V (sweep out)
Level: 5 V/TTL
Output impedance:1kΩ
Internal sweep
Selectable start and stop frequency
Internal sweep: all waveforms
Sweep time: linear from 20 ms to 100 s,
continuous or triggered
(ext. signal, interface)
Amplitude modulation:
Modulation via external signal
Modulation depth: 0 to 100 %
Bandwidth: DC - 20 kHz (-3 dB)
Gate (asynchronous)
Modulation on/off via external TTL signal
Delay time: ‹150ns
Input signal: TTL
Trigger function (synchronous)
Burst mode via ext. trigger input or interface
Frequency range: ‹ 500 kHz
Miscellaneous
Memory: For the last device settings and for 8 arbitrary signals
Safety class: Safety Class I (EN61010-1)
Power supply: 115/230V±10%; 50/60Hz
Power consumption: approx. 20 Watt
Operating temperature: +10° C to +40° C
Max. relative humidity: 10 %-90 % (without condensation)
Dimensions (W x H x D): 285 x 75 x 365 mm
Weight: approx. 5 kg
Accessories supplied: Operator’s Manual, power cable, software-CD
Optional accessories: HZ10 Silicone test leads, HZ33/HZ34 50 Ω Test Cable,
BNC-BNC, HZ24 Set of attenuators, 3/6/10 and 20 dB, HZ42 19” Rackmount kit
2RU, HZ20 Adapter Plug
To Next Page
Loading...
Need help?
General