Harman Kardon DC5300 - Technical Specifications; Model Specific Technical Data

Mode Test Point Adjustment : For ;
PB TP809 VR803 Adjust VR803 so the voltage at the test point is 0.62V when the
(Primary) leader tape is running and 200 mV or less in the middle of tape.
PB TP859 VR853 Adjust VR853 so the voltage at the test point is 0.62V when the
(Secondary) leader tape is running and 200 mV or less in the middle of tape.
TP501 (L ch), GND
. Maximum output
PB TP502 (R ch), GND Azimuth screw Lwin ce ; Ai
or OUTPUT jack Refer to “Azimuth Adjustment” on page 6.
TP501 (L ch), GND VR801 6020 Hz +20 Hz (TP806 : GND connection)
TP502 (R ch), GND Adjust at the center of test tape.
TP501 (L ch), GND 3010 Hz +10 Hz
gs TP502(Rch),GND | YR802 Adjust at the center of test tape.
PB TP501 (L ch), GND VR851 6020 Hz +20 Hz (TP856 : GND connection)
TP502 (R ch), GND Adjust at the center of test tape.
TP501 (L ch), GND 3010 Hz +10 Hz
PB TP502 (R ch), GND VR852 Adjust at the center of test tape.
775 mV
PB
TPS501
(L
ch),
GND
VR101
(L
ch)
:
x
(Primary) TP502 (Rch), GND —_| VR102(R ch) aoe Dai ue ta poewion:
775 mV
PB
TP501
(L
ch),
GND
VR157
(L
ch)
:
-
(Secondary) | TP502(Rch), GND __| VR158 (R ch) Neo
PB TP501 (L ch), GND VR103 Adjust VR103 and VR104 so the playback frequency response
(Primary) TP502 (R ch), GND VR104 (1 kHz/18 kHz) is +0.6 ~ 0.7 dB.
: or OUTPUT jack Refer to Fig. a
PB TP501 (L ch), GND VR153 Adjust VR153 and VR154 so the playback frequency response
(Secondar TP502 (R ch), GND VR154 (1 kHz/18 kHz) is +0.6 ~ 0.7 dB.
y or OUTPUT jack Refer to Fig. a
REC/PB TP101 (L ch), GND T301 105 kHz +3 kHz
(Primary) TP102 (R ch), GND Use METAL tape.
Minimum output
REC/PB 201 (leh) GND: | i201;L06202 Use METAL tape.
(Primary) TP202 (R ch), GND INPUT VR. minimum
VR351 35 mV .
VR352 Test tape is METAL blank tape.
REC/PB TP101 (L ch), GND VR353 20 mV
(Primary) TP102 (R ch), GND Test tape is CrOz2 blank tape.
13 mV
pica. Test tape is Normal blank tape.
560 mV
alah Vee Tape selector is METAL position.
EVEL knob : Adjust VR351 and VR352 so that the distortion becomes 1.0% — 1.4%
mV in REC/PB TP501 (L ch), GND 560 mV
tPrienaty) TP602 (R ch), GND oon Adjust VR353 so that the distortion becomes 1.3% (CrO2).
VR354 (Normal) Adjust VR354 so that the distortion becomes 1.0% (Normal).
This confiemation should be at each tape selector position.
VR353 So that the record/playback frequency resportion is flat (at least
L201, L202 within the range in Fig. b.)
TP50 (VR351, VR352) Tape selector is CrO2 position.
aire . So that the record/playback frequency resportion is flat (at least
REC/PB OUTPUT jack VR351 within the range in Fig. b.)
a VR352 Tape selector is METAL position.
VR354 So that the record/playback frequency resportion is flat (at least
L201, L202 within the range in Fig. b.)
(VR351, VR352) Tape selector is Normal position.
560 mV
ae to GND REC/PB Lea i an aN Perform adjustment using CrOz.
i 02 (R ch), Perform checking only for Normal and METAL tapes.
Load TCC-185C in SEC DECK and SCC-565 in PRI DECK and execute
high-speed copying, then play the tape in the PRI DECK. Check that
. the frequency response of the 14 kHz signal is within +3 dB of that
Covtae OUTPUT L203, L204 of the 1 kHz signal.
ORY Eray If this specification cannot be satisfied, adjust L203 and L204. After
adjustment is confirmed, also use the SCC-502 and SCC-1360 tapes
to check.
Load TCC-285C in SEC DECK and SCC-565 in PRI DECK and execute
high-speed copying, then play the tape in the PRI DECK. Check that
: the frequency response of the 14 kHz signal is within +3 dB of that
High Speed OUTPUT L203, L204 of the 1 kHz signal.
Copy Play if this specification cannot be satisfied, adjust L203 and L204. After
adjustment is confirmed, also use the SCC-502 and.SCC-1360 tapes
to check.
EVEL knob VR401 . :
dB below | REC/PAUSE PEAK LEVEL METER VR402 Adjust so the -1 dB segments light.
T jack. REC/PAUSE TP501 (L ch), GND LC501
02to GND | MP x filter TP502 (R ch), GND LC502 Adjust for -0.3 dB at 15 kHz and > 35 dB at 19 kHz
ON or OUTPUT jack