Location.No. Description Specification P/N Qty
HS200-PT01 metals part HS200-chassis
01.00.WJ.TJ.HS200.E00
1
1
HS200-PT02 metals part HS200-top cover
01.00.WJ.TJ.HS200.E00
2
1
HS200-PT03 metals part HS250-rear panel
01.00.WJ.TJ.HS250.E00
1
1
HS200-PT04 metals part
HS200-PCB plastic
frame(Left)
01.00.WJ.TJ.HS200.E00
5
1
HS200-PT05 metals part
HS200-PCB plastic
frame(Right)
01.00.WJ.TJ.HS200.E00
6
1
HS200-PT06 metals part
HS200-Connected Piece for
Speaker Jack
01.00.WJ.TJ.HS200.E00
7
4
HS200-PT07 Heatsink 50*62*65MM 01.00.WJ.TJ.E889 1
HS200-PT08 Heatsink 39*54.5*61mm 01.00.WJ.TJ.E890 1
HS200-PT09 Heatsink 122*45*51mm 01.00.WJ.TJ.E891 1
HS200-PT10 Heatsink 35*30*49mm 01.00.WJ.TJ.E892 1
For S503/S504/S505/S506 on SMPS
Board
Heatsink
16*12*51MM (The Hole's
depth is 18MM
01.00.WJ.TJ.E893 4
For U4 of Main Board Heatsink 28*28*10mm 01.00.WJ.TJ.E268 1
For U512 on SMPS Board (HS250-PT01) Heatsink
12*7.5*51MM (The Hole's
depth is 18MM
01.00.WJ.TJ.E982 1
For Amplifier Output Cord Magnetism annulus
F5BRFS11.7*6*19.75-3-
P.W
01.13.L.H.E034 2
HS200-RE01 plastic part HS250-front pannel 01.00.SJ.HS250.E002 1
HS200-RE02 plastic part HS200-2 in 1 Button 01.00.SJ.HS200.E002 1
HS200-RE03 plastic part HS200-Open button collar 01.00.SJ.HS200.E003 1
HS100-RE06 plastic part
HS100Volume Button
Collar
01.00.SJ.HS100.E006 1
HS200-RE04 plastic part HS200-Button Cover Board 01.00.SJ.HS200.E004 1
HS200-RE05 plastic part
HS200-Power Indicator
lampshade
01.00.SJ.HS200.E005 1
HS200-RE06 plastic part HS200-pedestal underlay 01.00.SJ.HS200.E006 2
HS200-RE07 plastic part HS200-Power Jack Jacket 01.00.SJ.HS200.E007 1
HS200-RE08 plastic part HS200-plastic scaleboard 01.00.SJ.HS200.E008 1
HS200-RE10 plastic part HS250-Large Lens 01.00.SJ.HS250.E001 1
HS100-RE10 plastic part HS100Volume Button 01.00.SJ.HS100.E010 1
HS100-RE08 plastic part
HS100volume button
lampshade
01.00.SJ.HS100.E008 1
plastic part
1000A-IR receiver support
5.5mm
01.00.SJ.1000A.E016 1
VFD filter 124.5*33.5*0.5mm 01.00.SJ.QT.E019 1
AC power Jack WS-044-0 01.40.CON.DCZ.E178 1
Metal logo
100mm "Harman/Kardon"
Thin Logo
01.00.SB.E036 1
Dustproof for Disc
tray door of Loder
LTD-1510 01.00.DP.JY.E135 1
For pedestal underlay HS100-H01 Silica gel gasket
50.6*4.2*1.5mm (with #500
glue be single sides glued )
01.00.DP.XJ.E192 4
For VFD (2) sponge
20*10*5MM (with #9448
glue be double sides glued )
01.00.DP.HM.E117 2
Between volume button and Front Panel
Board
Astigmatism PVC Φ45.5*Φ9.5mm 01.00.FZ.QT.153 1
Inside the volume button Mask PVC φ38.5 (Underside Glued) 01.00.FZ.QT.E253 1
For IR receiver sponge
10*10*7MM (with double
sides glued)
01.00.DP.HM.E364 1
Between AV Board and Heatsink sponge
20*10*4.5mm (with Single
side glued)
01.00.DP.HM.E160 1
paste in front of Disc tray door in the front
panel
High Soft sponge
124*10*2MM (with Single
side glued)
01.00.DP.HM.E378 1
pasted under U403 of AV Board
electric sponge 12*10*18mm 01.00.DD.PM.E183 1
Between front panel PCB and plastic part electric sponge 20*20*10MM 01.00.DD.PM.E271 1
Plastic fastener 12CM 01.00.FZ.QT.E122 3
For Q509 on SMPS Board Sil-pad sil-pad 400-3022 01.00.DP.QT.E113 1
For AV Board
Diathermanous
Selenium Rubber
16*11*1mm 01.00.DP.JY.E112 3
For SMPS Board Insulated PVC HS200-H01 01.00.DP.JY.E247 1
Be buckled above volume button board Insulated PVC HS200-H02 01.00.DP.JY.E249 1
HS250 Component List general
HS 250/230 Service Manual
To Next Page
Loading...
