Why is my Harman AVR 1510S not responding to the remote control?
If your Harman Receiver isn't responding to the remote control, start by changing the batteries in the remote. Then, make sure that nothing is blocking the remote sensor on the front of the receiver.
What to do if there is no sound from any speaker connected to my Harman Receiver?
If you're not getting any sound from any of the speakers connected to your Harman Receiver, it might be in protection mode. This can happen due to a possible short circuit. Check all speaker wires at both the speaker and AVR connections to ensure there are no crossed wires. If the problem persists, it could be due to internal issues, and you should contact your local Harman Kardon service center.
How to troubleshoot a Harman AVR 1510S that won't turn on?
If your Harman Receiver isn't turning on, first, ensure that the power cord is properly plugged into a working AC power outlet. Also, check to see if the AC outlet is controlled by a switch, and if so, make sure the switch is in the 'on' position.
What to do if my Harman AVR 1510S has a display but no sound or picture?
If your Harman Receiver's front-panel display is lit but you're not getting any sound or picture, try these steps: First, make sure all input and speaker connections are secure. Next, check if the Mute function is activated and, if so, press the Mute button to deactivate it. Finally, verify that the volume control isn't turned down too low and increase it as needed.
Why is there no sound from center or surround speakers on my Harman AVR 1510S Receiver?
If you're not hearing sound from the center or surround speakers connected to your Harman Receiver, first ensure that you've selected a surround mode other than stereo. Keep in mind that monophonic programs don't have surround information. Check the speaker configuration in the setup menu. Also, stereo programs may not always provide center or surround channel information.
How to fix intermittent buzzing in the tuner of my Harman Receiver?
If you're experiencing intermittent buzzing in the tuner of your Harman Receiver, it could be due to local interference. Try moving the receiver or antenna away from computers, fluorescent lights, motors, or other electrical appliances.
What to do if I can't activate remote control programming mode on my Harman AVR 1510S?
If you're unable to activate the remote control Programming mode on your Harman Receiver, make sure that you hold the Source Selector button for at least 3 seconds.
Lists the items included with the AVR.
Critical warnings and precautions for safe operation and installation.
Guidelines for proper placement and ventilation of the AVR unit.
Overview and diagram of controls located on the AVR's front panel.
Identification and description of all input and output connectors on the rear panel.
Explanation of buttons and their functions on the AVR's remote control.
Introduction to home theater systems, surround sound, and speaker placement strategies.
Details on connecting speakers, subwoofers, digital/analog audio, and video sources.
Guides for connecting TV, source devices, antennas, network, and power.
Instructions for installing batteries, programming, and reassigning remote control functions.
Step-by-step guide to configure the AVR, including speaker setup and audio settings.
How to assign source inputs, configure device settings, and establish network connectivity.
Guide to controlling volume, selecting sources, listening modes, and using the AVR.
Customizing AVR features like display, power, volume, HDMI, and network preferences.
Solutions for common operational issues, input problems, and remote control errors.
Technical details of the AVR's audio, tuner, video, and general performance characteristics.
Comprehensive tables for connection defaults, settings, and remote control product codes.
General| Channels | 5.1 |
|---|---|
| Network Connectivity | No |
| Input Sensitivity/Impedance | 200mV/47k ohms |
| Signal-to-Noise Ratio (IHF-A) | 100 dB |
| Input Level/Impedance (Video) | 1Vp-p/75 ohms |
| AM Tuner Frequency Range | 530 - 1710 kHz |
| HDMI Outputs | 1 |
| Signal-to-Noise Ratio | 100 dB |
| Power Output | 75W per channel (8 ohms) |
| Audio Formats Supported | Dolby TrueHD, DTS-HD Master Audio |
| Frequency Response | 10Hz to 100kHz |
| HDMI | Yes |
| FM Tuner Frequency Range | 87.5MHz – 108.0MHz |
| Power Requirement | AC 120V, 60Hz |
| Audio Inputs | 4 |
| Audio Outputs | 1 |
| Video Outputs | 1 |
| USB Port | 1 |
To Next Page
