Why is my Harman AVR 151S Receiver not responding to the remote control?
If your Harman Receiver isn't responding to the remote control, start by changing the batteries in the remote. Then, make sure that nothing is blocking the remote sensor on the front of the receiver.
What to do if there is no sound from any speaker connected to my Harman AVR 151S Receiver?
If you're not getting any sound from any of the speakers connected to your Harman Receiver, it might be in protection mode. This can happen due to a possible short circuit. Check all speaker wires at both the speaker and AVR connections to ensure there are no crossed wires. If the problem persists, it could be due to internal issues, and you should contact your local Harman Kardon service center.
How to troubleshoot a Harman Receiver that won't turn on?
If your Harman Receiver isn't turning on, first, ensure that the power cord is properly plugged into a working AC power outlet. Also, check to see if the AC outlet is controlled by a switch, and if so, make sure the switch is in the 'on' position.
What to do if my Harman AVR 151S Receiver has a display but no sound or picture?
If your Harman Receiver's front-panel display is lit but you're not getting any sound or picture, try these steps: First, make sure all input and speaker connections are secure. Next, check if the Mute function is activated and, if so, press the Mute button to deactivate it. Finally, verify that the volume control isn't turned down too low and increase it as needed.
Why is there no sound from center or surround speakers on my Harman Receiver?
If you're not hearing sound from the center or surround speakers connected to your Harman Receiver, first ensure that you've selected a surround mode other than stereo. Keep in mind that monophonic programs don't have surround information. Check the speaker configuration in the setup menu. Also, stereo programs may not always provide center or surround channel information.
How to fix intermittent buzzing in the tuner of my Harman Receiver?
If you're experiencing intermittent buzzing in the tuner of your Harman Receiver, it could be due to local interference. Try moving the receiver or antenna away from computers, fluorescent lights, motors, or other electrical appliances.
What to do if I can't activate remote control programming mode on my Harman AVR 151S?
If you're unable to activate the remote control Programming mode on your Harman Receiver, make sure that you hold the Source Selector button for at least 3 seconds.
General| Channels | 5.1 |
|---|---|
| Network Connectivity | No |
| Weight | 4.6 kg |
| Input Sensitivity/Impedance | 200mV/47k ohms |
| Signal-to-Noise Ratio (IHF-A) | 100 dB |
| Tuner Section Frequency Range | 87.5MHz – 108.0MHz |
| Video Section Input Level/Impedance | 1Vp-p/75 ohms |
| Video Frequency Response | 10Hz – 8MHz (–3dB) |
| Dimensions (H x W x D) | 121mm x 440mm x 300mm |
| Inputs HDMI | 4 |
| Inputs Analog Audio | 2 |
| Inputs Digital Audio (Coax/Optical) | 1 Coaxial, 1 Optical |
| Outputs HDMI | 1 |
| Outputs Headphone | 1 |
| Outputs Subwoofer Pre-out | 1 |
| Digital Audio Inputs | 1 Coaxial, 1 Optical |
| Dimensions (W x H x D) | 440mm x 121mm x 300mm |
| Dolby Technologies | Dolby Pro Logic II |
| DTS Technologies | DTS-HD Master Audio |
| USB Ports | 1 |
| Frequency Response (@ 1W) | 10Hz – 130kHz (+0dB/–3dB) |
| Power Requirement | AC 230V, 50Hz |
| Power Consumption | 300W maximum |
| Total Harmonic Distortion | 0.07% |
| Signal-to-Noise Ratio | 100 dB |
| Tuner | FM |
| Video Inputs/Outputs | 1 Output |
| Audio Inputs/Outputs | 2 in |
| HDMI | 3D, Audio Return Channel (ARC) |
Crucial safety warnings and precautions.
Explains power modes and button functions.
Details the USB port's capabilities and usage.
Controls for turning the AVR on and off.
Buttons to select input sources.
General guidance for speaker placement.
Specifics for LCR speaker positioning.
Specifics for surround speaker positioning.
Guidance on optimal subwoofer placement.
How to connect speakers using binding posts and spring clips.
General overview of connecting source devices.
Details on using HDMI for digital audio/video.
Illustrated guide for connecting speakers.
Instructions for connecting display devices.
Guide to connecting various source components.
Connecting devices with HDMI output.
Connecting the AVR to a power outlet.
Connecting the AVR to a home network.
Guide to programming remote codes.
Setting speaker presence and subwoofer modes.
Configuring source device inputs and settings.
Navigating the AVR's menus.
Setting crossover frequencies for each speaker.
Overview of speaker setup.
Setting speaker distance adjustments.
Setting crossover frequencies for speakers.
Calibrating speaker volume levels.
Measuring distances for speaker calibration.
Configuring network connections and settings.
How to adjust audio volume.
Tuning and managing radio stations.
Playing audio from Apple devices.
Accessing internet radio streams.
Playing audio files from USB devices.
Playing media from network-connected devices.
How to choose an input source.
Basic troubleshooting for video issues.
Specific HDMI connection troubleshooting.
How to choose surround sound modes.
Using Spotify Connect with the AVR.
Step-by-step guide for Spotify Connect.
Overview of advanced customization options.
How audio signals are processed.
Detailed explanation of surround sound modes.
Instructions for updating AVR firmware.
How to reset the AVR's processor.
Table describing various surround sound modes.
List of remote control button functions.
Continuation of remote control function list.
To Next Page
