Harman JBL VIBE200 TWS User Manual

BT connecting
BT connected
BT not connected
(BLue)
(BLue)
(BLue)
factory reset
(Blue/
white)
Low (RED)
(GREEN)
(ORANGE)
high
mid
Low (OFF)
(WHITE)
(WHITE)
high
mid
power
on &
CONNECT
ON
1
2
fully charged
Charging
(red orange
GREEN)
Stereo Mode
rL L/R
Mono Mode
DUAL CONNECT
1
2
quick
start
guide
Charging
TECH
SPEC
Choose "JBL VIBE200TWS" to connect
Settings Bluetooth
Bluetooth
DEVICES
Now Discoverable
Connected
JBL VIBE200TWS
Manual Controls
RECONNECT LEFT & RIGHT Factory resetConnect to a new Bluetooth device
up to
L/R L/R
led behaviors
WHAT’S
IN THE
BOX
how
to
wear
FIRST
TIME
USE
TAP × 1
HOLD (2
S)
TAP × 2
TAP × 3
HOLD (5S)
TAP × 3
TAP × 1
TAP × 2
L R
Bluetooth
BUTTON COMMAND
S / m / l
1
Try different sizes of eartips for best fit and seal.
2
S / M / L
1. Stereo Mode
2. Mono Mode
L R
Seamless
automatic
switch
Siri
®
/GOOGLE Assistant/Bixby Siri
®
/GOOGLE Assistant/Bixby
R
Siri
®
/GOOGLE Assistant/Bixby
power off
L+R
HOLD (5S)
Model: VIBE200TWS
Driver size: 8 mm/ 0.315” Dynamic Driver
Power supply: 5 V
1 A
Weight:
47.5 g/ 0.105 lbs
Headset battery type: Lithium-ion Battery (48 mAh/ 3.7 V)
Charging case battery type: Lithium-ion Battery(500 mAh/ 3.7 V)
Charging time: 2 hrs from empty
Music playtime with BT on: up to 5 hrs
Frequency response: 20 Hz – 20 kHz
Impedance: 16 ohm
Sensitivity:
108 dB SPL@1 kHz
Maximum SPL: 93 dB
Microphone sensitivity: -38 dBV/Pa @1 kHz
Bluetooth version: 5.0
Bluetooth profile version:
A2DP V1.3, AVRCP V1.6, HFP V1.7
Bluetooth transmitter frequency range: 2.400 GHz - 2.4835 GHz
Bluetooth transmitter power: 12 dBm
Bluetooth transmitter modulation: GFSK, π/4 QPSK, 8DPSK
Maximum operation temperature: 45°C

Harman JBL VIBE200 TWS Specifications

General

Brand	Harman
Model	JBL VIBE200 TWS
Category	Headphone
Language	English

Summary

What's in the Box

How to Wear Your Earbuds

First Time Use Setup

Power On and Connect

Dual Connect Modes

Stereo Mode

Describes stereo mode operation utilizing both left and right earbuds for immersive audio.

Mono Mode

Describes mono mode operation, allowing use of a single earbud for calls or audio.

Button Command Functions

Stereo Mode Button Commands

Lists button commands for stereo mode: tap, double-tap, triple-tap, and hold for voice assistant.

Mono Mode Button Commands

Lists button commands for mono mode: tap, double-tap, triple-tap, and hold for voice assistant.

Power Off Instructions

Manual Control Operations

Connect to New Bluetooth Device

Instructions for manually pairing the earbuds with a new Bluetooth-enabled device.

Reconnect Left and Right Earbuds

Steps to manually reconnect the left and right earbuds to the device or each other.

Factory Reset Procedure

Procedure to perform a factory reset on the earbuds to clear settings and pairings.

Charging Your Earbuds

LED Indicator Behaviors

Technical Specifications