Hatco FLAV-R-SAVOR FSDT-2 User Manual (English)

Other manuals for Hatco FLAV-R-SAVOR FSDT-2

Questions and Answers:

S
stephenturnerAug 17, 2025
What to do if my Hatco Commercial Food Equipment is plugged in but not working?
- W
  williamortizAug 17, 2025
  If your Hatco Commercial Food Equipment isn't working despite being plugged in, the issue could be due to no power reaching the unit. Check the electrical receptacle and ensure the power supply matches the unit's specifications. If the receptacle isn't working, check and reset the circuit breaker, or try plugging the unit into a different, known working receptacle.
K
Katherine JohnsonAug 20, 2025
Why is my Hatco Commercial Food Equipment not producing hot air?
- N
  Nicole FrancisAug 20, 2025
  Your Hatco Commercial Food Equipment might not be producing hot air due to several reasons: * Safety high-limit is tripped or open. * Incorrect voltage supplied to heating element. * Blower motor is not working. * Air heating element is defective. In these cases it is recommended to contact an authorized Hatco Service agent or Hatco for assistance.
A
Ann EvansAug 22, 2025
Why is my Hatco Commercial Food Equipment heating but not producing humidity, and the 'LO H20' is flashing?
- C
  Christine PerryAug 23, 2025
  If your Hatco Commercial Food Equipment is heating but not producing humidity, and the “LO H20” light flashes even though the unit is full of water, it could be due to using distilled water, which the low water probe can't sense because of the lack of minerals. Try adding 5 g (1 Tsp) of salt to the water reservoir during the initial fill.
J
Jorge DuncanAug 25, 2025
How to fix a Hatco FLAV-R-SAVOR FSDT-2 rotating rack that won't turn?
- R
  Rose SmithAug 26, 2025
  If your Hatco Commercial Food Equipment's rotating rack isn't turning, it might be because the proximity switch wasn't relocated after a door reversal. Refer to the “Relocating the Proximity Switch” section in the installation part of the manual for instructions. Other possible causes are proximity magnet or switch malfunctions, incorrect voltage to the rack motor, or a defective rack motor. In these cases it is recommended to contact an authorized Hatco Service agent or Hatco for assistance.
M
Mrs. Maria HolmesAug 27, 2025
How to fix a fluorescent lamp that is not working in my Hatco FLAV-R-SAVOR FSDT-2?
- N
  nicolehallAug 27, 2025
  If the fluorescent lamp in your Hatco Commercial Food Equipment isn't working, it could be either loose or defective. Try re-installing or replacing the fluorescent lamp. If the issue persists, the ballast may have failed, and you should contact an authorized Hatco Service agent or Hatco for assistance.
Z
zoebaldwinAug 30, 2025
What to do if my Hatco FLAV-R-SAVOR FSDT-2 Commercial Food Equipment operates but doesn't circulate air?
- J
  Jon RobertsonAug 30, 2025
  If your Hatco Commercial Food Equipment operates but isn't circulating air inside the cabinet, it could be due to a defective blower motor or incorrect voltage supplied to the blower. In these cases it is recommended to contact an authorized Hatco Service agent or Hatco for assistance.
A
Andrew KellySep 1, 2025
Why is my Hatco Commercial Food Equipment heating but not producing humidity when 'LO H20' is off?
- M
  Miranda GarciaSep 1, 2025
  If your Hatco Commercial Food Equipment is heating but not producing humidity, the “LO H20” light is not flashing on display and the unit is full of water, it could be due to incorrect voltage supplied to the water heating element or a defective heating element. In this case it is recommended to contact an authorized Hatco Service agent or Hatco for assistance.
L
Lisa JohnsonSep 4, 2025
Why is my Hatco Commercial Food Equipment not producing humidity even though it's full of water and the 'LO H20' light is flashing?
- E
  Emily WeeksSep 4, 2025
  If your Hatco Commercial Food Equipment unit is heating but not producing humidity, and the “LO H20” light flashes on the display even though the unit is full of water, it might be due to the use of distilled water, which lacks the minerals needed for the low water probe to function correctly. To resolve this, add one teaspoon of salt to the water reservoir upon initial fill. If the issue persists, it indicates that the low water protection system is malfunctioning, and it is best to contact an Authorized Hatco Service Agent or Hatco for assistance.
A
Amanda PotterSep 6, 2025
What to do if my Hatco Commercial Food Equipment is heating, but not producing humidity and the 'LO H20' light is off?
- M
  Michelle GutierrezSep 7, 2025
  If your Hatco Commercial Food Equipment unit is heating but not producing humidity, and the “LO H20” light is not flashing on the display, even though the unit is full of water, it is best to contact an Authorized Hatco Service Agent or Hatco for assistance, as this may indicate that incorrect voltage is supplied to the water heating element or the heating element is defective.
T
thomaswilliamSep 9, 2025
What to do if my Hatco Display Case is plugged in but not working?
- J
  Jonathan Wilson MDSep 9, 2025
  If your Hatco Display Case is plugged in but not functioning, first check the electrical receptacle to ensure it's working and that the power supply matches the unit's specifications. If the receptacle isn't working, check and reset the circuit breaker, or try plugging the unit into a different, known working receptacle.