EasyManua.ls Logo

Haulotte Group 3522A - User Manual

Haulotte Group 3522A
142 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OPERATOR’S & MAINTENANCE
MANUAL
B33-01-0093 Rev 4
May 2013

Table of Contents

Questions and Answers

  • M
    Mrs. Jeanette Kaufman MDJul 31, 2025
    What to do if there are no lights on the panel of Haulotte Group 3522A Boom Lifts?
    • M
      Miranda JohnsonJul 31, 2025
      If the panel lights don't turn on when you switch the key to the 'on' position, here's what you should check: * First, make sure the EMERGENCY STOP is not engaged. Disengage it if it is. * Check the battery charge and recharge if needed. * Inspect and repair any loose battery connections, including the ground or in-series cable. * Ensure the battery main disconnect is plugged in. * Finally, check for blown fuses and replace them if necessary.
  • W
    wellscynthiaAug 10, 2025
    How to fix outrigger indicator LED lights on Haulotte Group Boom Lifts?
    • L
      Levi GriffinAug 10, 2025
      If the outrigger indicator LED lights aren't working on your Haulotte Group Boom Lifts, try these steps: * Make sure the key switch is turned to the ground controls position. * Disengage the EMERGENCY STOP buttons. * Deploy all outriggers.
  • R
    robinsonanthonyAug 15, 2025
    What to do if hydraulic function does not work and display window shows an error message on Haulotte Group 3522A Boom Lifts?
    • J
      Jose FloydAug 15, 2025
      If the hydraulic function isn't working and the display shows an error message, it could be due to an error detected by the safety interlock microprocessor or an electric or electronic failure. Refer to error code definitions in Table 3-3.
  • J
    Jennifer LopezAug 20, 2025
    What does error code on ground control panel of Haulotte Group 3522A Boom Lifts mean?
    • D
      David BarkerAug 20, 2025
      If an error code is displayed on the Ground Control Panel, it means an error has been detected by the Control Box. Refer to Error Code Definitions, Table 3-3.
  • T
    Tiffany Thomas DVMAug 25, 2025
    What does a flashing green light on the motor controller of Haulotte Group Boom Lifts mean?
    • V
      vleonAug 26, 2025
      If you see a green light flashing on the Motor Controller, it indicates an error has been detected by the Motor Controller. Refer to Motor Controller Error Code Definitions, Table 3-4.
  • M
    mitchellkevinNov 4, 2025
    Why aren't the telescoping boom controls working on my Haulotte Group Boom Lifts?
    • A
      Alyssa GeorgeNov 4, 2025
      If the telescoping boom controls on your Haulotte Group Boom Lifts aren't functioning correctly, intermittently, or at all, consider the following potential causes and solutions: 1. Ensure the key switch is in the correct position (ground or platform controls). 2. Check the battery charge and recharge if low. 3. Disengage the EMERGENCY STOP button if it's engaged. 4. Inspect and repair any loose battery ground or in-series cable connections. 5. Deploy all outriggers properly to level the aerial work platform. 6. Inspect the hydraulic pump and repair or replace if needed. 7. Check wiring terminals in the control box and at the valve manifold for loose connectors; repair or replace as needed. 8. Clean the valve solenoid and recheck its function; repair or replace if needed. 9. Insp...

Summary

Safety Information

Safety Advisories Legend

Explains the meaning of DANGER, WARNING, CAUTION, and NOTICE symbols used in the manual.

Pre-Operation Safety Checks

Outlines essential safety precautions to be followed before operating the aerial work platform.

During Operation Safety

Details general safety precautions to be observed while operating the aerial work platform.

Fall Protection Guidelines

Specifies requirements for occupant safety, including harness use and platform stability.

Wind Loading Hazards

Explosion Hazard Precautions

Operation Procedures

Ground Control Panel

Describes the controls and functions available at the ground-level operating station.

Platform Control Panel

Explains the controls and functions available at the platform-level operating station.

Normal Operating Procedure

Provides a step-by-step guide for the standard operation of the aerial work platform.

Manual Boom Operation

Details procedures for manual boom control during power interruptions or failures.

Towing the Aerial Work Platform

Covers essential checks and procedures for safely towing the aerial work platform.

Equipment Maintenance

Battery Recharge and Fault Codes

Daily Service Checks

Details routine checks to be performed daily or before each operation.

Calibration Procedures

Troubleshooting and Error Codes

Addresses common problems, error codes for controls and motor controller.

Cylinder Replacement Procedures

Master and Slave Cylinder Replacement

Lift Cylinder Replacement

Outrigger Cylinder Replacement

Optional Equipment

Drive and Set Option

Axle and Related Components

Dexter Axle Components and Maintenance

Brake System Troubleshooting

Provides guidance for troubleshooting hydraulic and electric braking systems.

Bradley Brake Adjustment and Testing

Haulotte Group 3522A Specifications

General IconGeneral
BrandHaulotte Group
Model3522A
CategoryBoom Lifts
LanguageEnglish

Related product manuals