Haulotte HA32RTJ PRO - User Manual

Questions and Answers

L
longrachelAug 21, 2025
Why platform controls do not respond on Haulotte HA32RTJ PRO?
- R
  rcardenasAug 21, 2025
  If the platform controls of your Haulotte Boom Lift do not respond, it could be due to several reasons: * The ground control box selector key might be set to the ground control box position. Turn the ground control box selector key to platform control box position. * The 'Enable Switch' control validation device may not be enabled. Enable the device and keep it pressed down during movement. * The 'Dead man' control validation device might be activated for more than 8 seconds without movement. Release the 'Dead man' selector and reactivate it. * Not enough hydraulic oil: Top up the oil level. For other issues like a faulty joystick or solenoid valve, it is recommended to contact HAULOTTE Services®.
H
Hannah RhodesAug 23, 2025
What to do if Haulotte HA32RTJ PRO engine shuts down and fuel tank indicator is lit?
- J
  Jessica WallaceAug 23, 2025
  If the engine shuts down and the fuel tank indicator is lit up on your Haulotte Boom Lift, it means the fuel tank is empty. Refill the tank to resolve this issue.
S
Sydney HickmanAug 26, 2025
Why is there low hydraulic pump pressure in my Haulotte HA32RTJ PRO?
- M
  Melissa CookAug 26, 2025
  If you experience low hydraulic pump pressure or power in your Haulotte Boom Lift, consider the following: * **Clogged air filter**: Replace the filter. * **Clogged oil filter**: Replace the oil filter cartridge. * **Clogged fuel filter**: Replace the filter. * **Faulty accelerator coil**: Replace the coil. * **Faulty accelerator fuse or relay**: Replace the accelerator relay or fuse. For issues like engine speed being too low or leak/air in the fuel circuit, it is recommended to contact HAULOTTE Services®.
C
castrobrianAug 27, 2025
What causes the overload indicator and buzzer to activate with unresponsive platform controls in Haulotte Boom Lifts?
- C
  Crystal MorenoAug 28, 2025
  If the platform controls of your Haulotte Boom Lift do not respond, the buzzer is on, and the overload indicator is on, it could be due to: * **Platform overload**: Remove some weight to not exceed the authorized limit. * **Platform touching the ground**: Lift the jib from the ground control box. * **Jib cylinder at the lower or upper mechanical stop position**: Control the jib from the ground control box. * **Jib in transport position**: Control the jib from the ground control box. For a faulty weighing system, it is recommended to contact HAULOTTE Services®.
B
barnettelizabethAug 30, 2025
What does it mean when the radius limit indicator is on and platform controls do not respond in Haulotte HA32RTJ PRO Boom Lifts?
- J
  Julie FloresAug 30, 2025
  If the platform controls of your Haulotte Boom Lift do not respond and the radius limit indicator is on when a movement control is activated, it means the movement is not permitted. Bring the machine back within the authorized zone by retracting the telescope, lowering the boom, or lifting the arm to enable movement.
A
ahoustonSep 1, 2025
What to do when the tilt indicator is on, buzzer sounds, and platform controls are unresponsive on Haulotte Boom Lifts?
- A
  aaronwilliamsSep 1, 2025
  If the platform controls of your Haulotte Boom Lift do not respond and the buzzer is sounding because the tilt indicator is on, it means the tilt or slope exceeds the authorized limit. Stow the machine and move to flat ground.
K
Kelly MoraSep 4, 2025
What does it mean when Haulotte HA32RTJ PRO engine stops during boom movement and the defect indicator flashes twice?
- D
  Daniel GibsonSep 4, 2025
  If the engine stops during boom movement, will not restart, and the defect indicator flashes in sequences of 2 flashes on your Haulotte Boom Lift, it may be due to faulty platform control box joystick(s). It is recommended to contact HAULOTTE Services® to replace the joystick(s).
S
Sydney CharlesSep 6, 2025
Why won't the axles retract/extend and the buzzer is sounding on my Haulotte HA32RTJ PRO?
- D
  Deborah RuizSep 6, 2025
  If the axles of your Haulotte Boom Lift do not retract/extend and the buzzer is sounding, it means the machine is not in the required configuration. Turn the ground control box selector key to the ground control box position, stow the machine completely, and align the turret with the machine.
R
Raymond JensenSep 8, 2025
What causes a discontinuous buzzer and no driving in Haulotte Boom Lifts?
- T
  Theresa RoseSep 8, 2025
  If your Haulotte Boom Lift is not driving and a discontinuous buzzer is sounding, it indicates that the platform is at the working limit. Retract the boom telescope to resolve this issue.
S
Scott DaySep 12, 2025
What does it mean when the overload indicator is on, buzzer sounds, defect indicator flashes 9 times, and platform controls are unresponsive on Haulotte Boom Lifts?
- M
  Maria BenjaminSep 12, 2025
  If the platform controls of your Haulotte Boom Lift do not respond, the buzzer is on, the overload indicator is on, and the defect indicator flashes in sequences of 9 flashes, it indicates a faulty platform overload circuit. Reinitialize the system. If the problem persists, it is recommended to contact HAULOTTE Services® to check the electrical weighing circuit.

Summary

Safety Precautions

Recommendations for Safe Operation

General advice and guidelines for safe operation and maintenance.

Manufacturers Warranty Details

Details on warranty terms, conditions, and acceptance procedures.

Scope of Intervention and Responsibilities

Defines responsibilities and scope for maintenance and inspections.

Intervention Safety Instructions

Safety guidelines and precautions for performing maintenance tasks.

Recommendations

Lubrication Diagram and Points

Visual guide showing lubrication points and types for the machine.

Consumables and Part Codes

List of fluids, filters, and other consumables with part codes.

Decals and Markings Locations

Identifies the placement and meaning of safety decals and markings.

Maintenance Procedures

Maintenance Schedule and Intervals

Table outlining maintenance tasks, frequencies, and periodicity.

Inspection Program Overview

Details the types and intervals for machine inspections.

Daily Inspection Checklist

Procedures and checklists for daily pre-operation checks.

Periodic Inspection Guidelines

Guidelines for regular inspections beyond daily checks.

Reinforced Inspection Procedures

In-depth inspection procedures performed at longer intervals.

Major Inspection Requirements

Comprehensive inspection for long-term suitability and proper function.

Specific Maintenance Sheets

Specific procedures for maintenance tasks like oil changes and filter replacement.

Diagnosis and Troubleshooting

Pre-Troubleshooting Recommendations

Initial checks for common malfunctions before troubleshooting.

Troubleshooting Guide by Problem

Table of problems, probable causes, and solutions for diagnostics.

Electric Circuit Details

Wiring Diagram - Main Components

Nomenclature and identification of key electrical components.

Fuse Identification and Locations

Identification and location of fuses within the electrical system.

Relays and Terminals Identification

Identification of relays and terminal points on the circuit board.

Connector Mapping and Functions

Mapping of connectors to their respective functions and locations.

Diagnosis Indicators and Safety Features

Explains indicators, safety features, buzzers, and alerts.

Hydraulic Circuit Details

Hydraulic Diagram - Main Components

Overview of main hydraulic system components and their layout.

Solenoid Valve Locations

Identifies solenoid valves and their locations in the hydraulic system.

Intervention Register

Maintenance and Repair Logbook

Logbook for recording maintenance and repair work performed on the machine.

Electrical Diagrams

Diagrams for HA32 RTJ, HA100 RTJ, HA41 RTJ, HA130 RTJ PRO

Detailed electrical wiring diagrams for the specified machine models.

Hydraulic Diagrams

Hydraulic Diagrams for HA32 RTJ, HA100 RTJ PRO

Hydraulic diagrams for specific machine models.

Hydraulic Diagrams for HA41 RTJ, HA130 RTJ PRO

Hydraulic diagrams for specific machine models.

Haulotte HA32RTJ PRO Specifications

General

Power Source	Diesel
Drive Type	4WD
Gradeability	40%
Rotation	360° Continuous
Fuel Type	Diesel
Horizontal Outreach	22 ft 6 in
Lift Capacity	500 lbs
Platform Capacity	500 lbs
Steering	4-Wheel Steering