Haussmann X-PERT HETS-001

Questions and Answers

B
brandy40Aug 16, 2025
What to do if my Haussmann X-PERT HETS-001 will not start?
- M
  Megan MillerAug 16, 2025
  If your Haussmann Saw won't start, there are several potential causes: * The saw might not be plugged in; ensure it is properly connected. * A fuse may be blown or a circuit breaker tripped; replace the fuse or reset the breaker. * The power cord could be damaged, requiring replacement. * There might be debris in the on/off switch; remove the switch, separate it, and clean out any accumulated debris.
S
Sandra OnealAug 19, 2025
Why is material kicked back from the blade of my Haussmann X-PERT HETS-001 Saw?
- D
  deanna00Aug 19, 2025
  If material kicks back from the blade of your Haussmann Saw, consider these possible causes and solutions: 1. The rip fence may be out of adjustment; align it with the mitre gauge slot. 2. The splitter might not be aligned with the blade; ensure proper alignment. 3. You may be feeding stock without a rip fence; install and use the rip fence. 4. The splitter may not be in place; install and use the splitter with guard. 5. A dull blade could be the culprit; replace it. 6. The operator might be releasing the material too soon; push the material completely past the saw blade before releasing. 7. The mitre angle lock knob might not be tight; tighten the knob.
W
Whitney WilsonAug 22, 2025
Why does my Haussmann Saw make unsatisfactory cuts?
- J
  Jose TaylorAug 22, 2025
  Unsatisfactory cuts from your Haussmann Saw can stem from several issues: * The blade may be dull; replace it. * The blade might be mounted backwards; turn it around. * Gum or pitch may be on the blade; remove the blade and clean it with turpentine and coarse steel wool. * The wrong blade may be in use for the task; change the blade. * Gum or pitch on the blade can cause erratic feed; clean the table with turpentine and steel wool.
R
Ronald DavisAug 25, 2025
Why does my Haussmann Saw vibrate excessively?
- M
  Mr. Jordan RojasAug 26, 2025
  Excessive vibration in your Haussmann Saw can be due to: * The saw not being securely mounted to the workbench; tighten all mounting hardware. * The bench being on an uneven floor; reposition it on a flat, level surface. * A damaged saw blade; replace the blade.
P
Patricia LopezAug 28, 2025
How to fix inaccurate 45° and 90° rip cuts on a Haussmann X-PERT HETS-001 Saw?
- C
  Calvin ArmstrongAug 28, 2025
  Inaccurate 45° and 90° rip cuts with your Haussmann Saw can be caused by: * A positive stop not adjusted correctly; check the blade with a square and adjust the positive stop. * A tilt angle pointer not set accurately; check the blade with a square and adjust to zero.
I
igrayAug 31, 2025
Why doesn't the blade of my Haussmann Saw come up to speed?
- A
  Amber AvilaAug 31, 2025
  If your Haussmann Saw blade doesn't reach full speed or the reset trips too easily, it could be because: * The extension cord is too light or too long; replace it with an adequate size cord. * There's low house voltage; contact your electric company.
M
Mr. Matthew Buck MDSep 3, 2025
What to do if material pinches the blade of my Haussmann X-PERT HETS-001 Saw when ripping?
- D
  Derek JohnsonSep 3, 2025
  If material pinches the blade when ripping with your Haussmann Saw: * The rip fence might not be aligned with the blade; check and adjust the rip fence. * The wood may be warped, with an edge that isn't straight against the fence; select another piece of wood.
W
williamschristopherSep 5, 2025
How to fix inaccurate 45° and 90° crosscuts on a Haussmann Saw?
- C
  Chase YoungSep 6, 2025
  If your Haussmann Saw does not make accurate 45° and 90° crosscuts, the mitre gauge might be out of adjustment. Adjust the mitre gauge.
D
Danielle RaymondSep 9, 2025
Why does material bind on the splitter of my Haussmann X-PERT HETS-001 Saw?
- B
  Benjamin RodriguezSep 9, 2025
  If material binds on the splitter of your Haussmann Saw, the splitter might not be aligned correctly with the blade. Check and align the splitter with the blade.
A
anthonyleeSep 12, 2025
Why doesn't the blade of my Haussmann Saw raise or tilt freely?
- M
  Michael RobinsonSep 12, 2025
  If the blade of your Haussmann Saw does not raise or tilt freely, it may be due to sawdust and dirt in the elevation/tilting mechanisms. Brush or blow out any loose dust and dirt.